0

HifiBerry DAC2 Pro xlr unable to record sound

Hi, I am configuring the Hifiberry DAC2 pro xlr, and it somehow is detecting the the playback device, but it is not able to detect the mic that I have attached to it. I have two mics and it somehow not working.

rpi@raspberrypi:~ $ aplay -l
**** List of PLAYBACK Hardware Devices ****
card 0: sndrpihifiberry [snd_rpi_hifiberry_dacplus], device 0: HiFiBerry DAC+ Pro HiFi pcm512x-hifi-0 [HiFiBerry DAC+ Pro HiFi pcm512x-hifi-0]
  Subdevices: 1/1
  Subdevice #0: subdevice #0


rpi@raspberrypi:~ $ arecord -l
**** List of CAPTURE Hardware Devices ****


rpi@raspberrypi:~ $ uname -a
Linux raspberrypi 5.15.70-v7l+ #1590 SMP Tue Sep 27 15:58:00 BST 2022 armv7l GNU/Linux


rpi@raspberrypi:~ $ lsb_release -a
No LSB modules are available.
Distributor ID: Raspbian
Description:    Raspbian GNU/Linux 11 (bullseye)
Release:        11
Codename:       bullseye

/boot/config.txt

# For more options and information see
# http://rpf.io/configtxt
# Some settings may impact device functionality. See link above for details

# uncomment if you get no picture on HDMI for a default "safe" mode
#hdmi_safe=1

# uncomment the following to adjust overscan. Use positive numbers if console
# goes off screen, and negative if there is too much border
#overscan_left=16
#overscan_right=16
#overscan_top=16
#overscan_bottom=16

# uncomment to force a console size. By default it will be display's size minus
# overscan.
#framebuffer_width=1280
#framebuffer_height=720

# uncomment if hdmi display is not detected and composite is being output
#hdmi_force_hotplug=1

# uncomment to force a specific HDMI mode (this will force VGA)
#hdmi_group=1
#hdmi_mode=1

# uncomment to force a HDMI mode rather than DVI. This can make audio work in
# DMT (computer monitor) modes
#hdmi_drive=2

# uncomment to increase signal to HDMI, if you have interference, blanking, or
# no display
#config_hdmi_boost=4

# uncomment for composite PAL
#sdtv_mode=2

#uncomment to overclock the arm. 700 MHz is the default.
#arm_freq=800

# Uncomment some or all of these to enable the optional hardware interfaces
dtparam=i2c_arm=on
#dtparam=i2s=on
dtparam=spi=on

# Uncomment this to enable infrared communication.
#dtoverlay=gpio-ir,gpio_pin=17
#dtoverlay=gpio-ir-tx,gpio_pin=18

# Additional overlays and parameters are documented /boot/overlays/README


# Enable audio (loads snd_bcm2835)
dtoverlay=hifiberry-dacplus

# Automatically load overlays for detected cameras
start_x=1

# Automatically load overlays for detected DSI displays
display_auto_detect=1

# Enable DRM VC4 V3D driver
#dtoverlay=vc4-kms-v3d
max_framebuffers=2

# Disable compensation for displays with overscan
disable_overscan=1
[cm4]
# Enable host mode on the 2711 built-in XHCI USB controller.
# This line should be removed if the legacy DWC2 controller is required
# (e.g. for USB device mode) or if USB support is not required.
otg_mode=1

[all]

[pi4]
dtoverlay=vc4-fkms-v3d,audio=off
force_eeprom_read=0
# Run as fast as firmware / board allows
arm_boost=1
dtdebug=1

[all]
enable_uart=1
gpu_mem=128

 

dmesg
[    0.000000] Booting Linux on physical CPU 0x0
[    0.000000] Linux version 5.15.70-v7l+ (dom@buildbot) (arm-linux-gnueabihf-gcc-8 (Ubuntu/Linaro 8.4.0-3ubuntu1) 8.4.0, GNU ld (GNU Binutils for Ubuntu) 2.34) #1590 SMP Tue Sep 27 15:58:00 BST 2022
[    0.000000] CPU: ARMv7 Processor [410fd083] revision 3 (ARMv7), cr=30c5383d
[    0.000000] CPU: div instructions available: patching division code
[    0.000000] CPU: PIPT / VIPT nonaliasing data cache, PIPT instruction cache
[    0.000000] OF: fdt: Machine model: Raspberry Pi 4 Model B Rev 1.2
[    0.000000] random: crng init done
[    0.000000] Memory policy: Data cache writealloc
[    0.000000] Reserved memory: created CMA memory pool at 0x000000001ac00000, size 320 MiB
[    0.000000] OF: reserved mem: initialized node linux,cma, compatible id shared-dma-pool
[    0.000000] Zone ranges:
[    0.000000]   DMA      [mem 0x0000000000000000-0x000000002fffffff]
[    0.000000]   Normal   empty
[    0.000000]   HighMem  [mem 0x0000000030000000-0x00000000fbffffff]
[    0.000000] Movable zone start for each node
[    0.000000] Early memory node ranges
[    0.000000]   node   0: [mem 0x0000000000000000-0x0000000037ffffff]
[    0.000000]   node   0: [mem 0x0000000040000000-0x00000000fbffffff]
[    0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x00000000fbffffff]
[    0.000000] percpu: Embedded 16 pages/cpu s35788 r8192 d21556 u65536
[    0.000000] pcpu-alloc: s35788 r8192 d21556 u65536 alloc=16*4096
[    0.000000] pcpu-alloc: [0] 0 [0] 1 [0] 2 [0] 3 
[    0.000000] Built 1 zonelists, mobility grouping on.  Total pages: 997696
[    0.000000] Kernel command line: coherent_pool=1M 8250.nr_uarts=1 snd_bcm2835.enable_compat_alsa=0 snd_bcm2835.enable_hdmi=1  smsc95xx.macaddr=DC:A6:32:77:9B:D9 vc_mem.mem_base=0x3ec00000 vc_mem.mem_size=0x40000000  console=ttyS0,115200 console=tty1 root=PARTUUID=bd15ad91-02 rootfstype=ext4 fsck.repair=yes rootwait quiet splash plymouth.ignore-serial-consoles
[    0.000000] Unknown kernel command line parameters "splash", will be passed to user space.
[    0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes, linear)
[    0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes, linear)
[    0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off
[    0.000000] software IO TLB: mapped [mem 0x0000000014890000-0x0000000018890000] (64MB)
[    0.000000] Memory: 3548544K/3997696K available (10240K kernel code, 1385K rwdata, 3304K rodata, 2048K init, 592K bss, 121472K reserved, 327680K cma-reserved, 3211264K highmem)
[    0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
[    0.000000] ftrace: allocating 35501 entries in 105 pages
[    0.000000] ftrace: allocated 105 pages with 4 groups
[    0.000000] trace event string verifier disabled
[    0.000000] rcu: Hierarchical RCU implementation.
[    0.000000]  Rude variant of Tasks RCU enabled.
[    0.000000]  Tracing variant of Tasks RCU enabled.
[    0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies.
[    0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16
[    0.000000] GIC: Using split EOI/Deactivate mode
[    0.000000] arch_timer: cp15 timer(s) running at 54.00MHz (phys).
[    0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0xc743ce346, max_idle_ns: 440795203123 ns
[    0.000000] sched_clock: 56 bits at 54MHz, resolution 18ns, wraps every 4398046511102ns
[    0.000018] Switching to timer-based delay loop, resolution 18ns
[    0.000346] Console: colour dummy device 80x30
[    0.000406] printk: console [tty1] enabled
[    0.000474] Calibrating delay loop (skipped), value calculated using timer frequency.. 108.00 BogoMIPS (lpj=540000)
[    0.000504] pid_max: default: 32768 minimum: 301
[    0.000644] LSM: Security Framework initializing
[    0.000839] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes, linear)
[    0.000866] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes, linear)
[    0.002374] cgroup: Disabling memory control group subsystem
[    0.002603] CPU: Testing write buffer coherency: ok
[    0.002658] CPU0: Spectre BHB: enabling loop workaround for all CPUs
[    0.003084] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
[    0.004396] Setting up static identity map for 0x200000 - 0x20003c
[    0.004609] rcu: Hierarchical SRCU implementation.
[    0.005581] smp: Bringing up secondary CPUs ...
[    0.006694] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001
[    0.007946] CPU2: thread -1, cpu 2, socket 0, mpidr 80000002
[    0.009197] CPU3: thread -1, cpu 3, socket 0, mpidr 80000003
[    0.009366] smp: Brought up 1 node, 4 CPUs
[    0.009389] SMP: Total of 4 processors activated (432.00 BogoMIPS).
[    0.009407] CPU: All CPU(s) started in HYP mode.
[    0.009420] CPU: Virtualization extensions available.
[    0.010165] devtmpfs: initialized
[    0.025106] VFP support v0.3: implementor 41 architecture 3 part 40 variant 8 rev 0
[    0.025321] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[    0.025352] futex hash table entries: 1024 (order: 4, 65536 bytes, linear)
[    0.034678] pinctrl core: initialized pinctrl subsystem
[    0.035862] NET: Registered PF_NETLINK/PF_ROUTE protocol family
[    0.039960] DMA: preallocated 1024 KiB pool for atomic coherent allocations
[    0.040721] audit: initializing netlink subsys (disabled)
[    0.040974] audit: type=2000 audit(0.040:1): state=initialized audit_enabled=0 res=1
[    0.041596] thermal_sys: Registered thermal governor 'step_wise'
[    0.042367] hw-breakpoint: found 5 (+1 reserved) breakpoint and 4 watchpoint registers.
[    0.042387] hw-breakpoint: maximum watchpoint size is 8 bytes.
[    0.042773] Serial: AMBA PL011 UART driver
[    0.054992] bcm2835-mbox fe00b880.mailbox: mailbox enabled
[    0.090042] raspberrypi-firmware soc:firmware: Attached to firmware from 2022-09-30T14:26:36, variant start_x
[    0.100060] raspberrypi-firmware soc:firmware: Firmware hash is afe2b3f5f60315137568e903508e7eae8b6543a4
[    0.158826] Kprobes globally optimized
[    0.164734] bcm2835-dma fe007000.dma: DMA legacy API manager, dmachans=0x1
[    0.169112] vgaarb: loaded
[    0.169558] SCSI subsystem initialized
[    0.169781] usbcore: registered new interface driver usbfs
[    0.169840] usbcore: registered new interface driver hub
[    0.169923] usbcore: registered new device driver usb
[    0.170586] usb_phy_generic phy: supply vcc not found, using dummy regulator
[    0.170780] usb_phy_generic phy: dummy supplies not allowed for exclusive requests
[    0.171088] pps_core: LinuxPPS API ver. 1 registered
[    0.171102] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[    0.171130] PTP clock support registered
[    0.172756] clocksource: Switched to clocksource arch_sys_counter
[    0.253467] VFS: Disk quotas dquot_6.6.0
[    0.253571] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[    0.253753] FS-Cache: Loaded
[    0.253960] CacheFiles: Loaded
[    0.264520] NET: Registered PF_INET protocol family
[    0.264743] IP idents hash table entries: 16384 (order: 5, 131072 bytes, linear)
[    0.266284] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes, linear)
[    0.266318] Table-perturb hash table entries: 65536 (order: 6, 262144 bytes, linear)
[    0.266344] TCP established hash table entries: 8192 (order: 3, 32768 bytes, linear)
[    0.266408] TCP bind hash table entries: 8192 (order: 4, 65536 bytes, linear)
[    0.266477] TCP: Hash tables configured (established 8192 bind 8192)
[    0.266618] UDP hash table entries: 512 (order: 2, 16384 bytes, linear)
[    0.266655] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes, linear)
[    0.266900] NET: Registered PF_UNIX/PF_LOCAL protocol family
[    0.273620] RPC: Registered named UNIX socket transport module.
[    0.273637] RPC: Registered udp transport module.
[    0.273651] RPC: Registered tcp transport module.
[    0.273665] RPC: Registered tcp NFSv4.1 backchannel transport module.
[    0.273686] PCI: CLS 0 bytes, default 64
[    1.296878] hw perfevents: enabled with armv7_cortex_a7 PMU driver, 7 counters available
[    1.320196] Initialise system trusted keyrings
[    1.320482] workingset: timestamp_bits=14 max_order=20 bucket_order=6
[    1.329454] zbud: loaded
[    1.331296] FS-Cache: Netfs 'nfs' registered for caching
[    1.332152] NFS: Registering the id_resolver key type
[    1.332192] Key type id_resolver registered
[    1.332207] Key type id_legacy registered
[    1.332334] nfs4filelayout_init: NFSv4 File Layout Driver Registering...
[    1.332349] nfs4flexfilelayout_init: NFSv4 Flexfile Layout Driver Registering...
[    1.333515] Key type asymmetric registered
[    1.333532] Asymmetric key parser 'x509' registered
[    1.333761] bounce: pool size: 64 pages
[    1.333822] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 247)
[    1.334053] io scheduler mq-deadline registered
[    1.334070] io scheduler kyber registered
[    1.342992] brcm-pcie fd500000.pcie: host bridge /scb/pcie@7d500000 ranges:
[    1.343033] brcm-pcie fd500000.pcie:   No bus range found for /scb/pcie@7d500000, using [bus 00-ff]
[    1.343128] brcm-pcie fd500000.pcie:      MEM 0x0600000000..0x063fffffff -> 0x00c0000000
[    1.343229] brcm-pcie fd500000.pcie:   IB MEM 0x0000000000..0x00bfffffff -> 0x0400000000
[    1.404860] brcm-pcie fd500000.pcie: link up, 5.0 GT/s PCIe x1 (SSC)
[    1.405239] brcm-pcie fd500000.pcie: PCI host bridge to bus 0000:00
[    1.405259] pci_bus 0000:00: root bus resource [bus 00-ff]
[    1.405281] pci_bus 0000:00: root bus resource [mem 0x600000000-0x63fffffff] (bus address [0xc0000000-0xffffffff])
[    1.405367] pci 0000:00:00.0: [14e4:2711] type 01 class 0x060400
[    1.405608] pci 0000:00:00.0: PME# supported from D0 D3hot
[    1.409359] PCI: bus0: Fast back to back transfers disabled
[    1.409708] pci 0000:01:00.0: [1106:3483] type 00 class 0x0c0330
[    1.409837] pci 0000:01:00.0: reg 0x10: [mem 0x00000000-0x00000fff 64bit]
[    1.410267] pci 0000:01:00.0: PME# supported from D0 D3cold
[    1.414000] PCI: bus1: Fast back to back transfers disabled
[    1.414059] pci 0000:00:00.0: BAR 8: assigned [mem 0x600000000-0x6000fffff]
[    1.414086] pci 0000:01:00.0: BAR 0: assigned [mem 0x600000000-0x600000fff 64bit]
[    1.414170] pci 0000:00:00.0: PCI bridge to [bus 01]
[    1.414196] pci 0000:00:00.0:   bridge window [mem 0x600000000-0x6000fffff]
[    1.414599] pcieport 0000:00:00.0: enabling device (0140 -> 0142)
[    1.414839] pcieport 0000:00:00.0: PME: Signaling with IRQ 62
[    1.422945] Serial: 8250/16550 driver, 1 ports, IRQ sharing enabled
[    1.425909] iproc-rng200 fe104000.rng: hwrng registered
[    1.426228] vc-mem: phys_addr:0x00000000 mem_base=0x3ec00000 mem_size:0x40000000(1024 MiB)
[    1.427704] gpiomem-bcm2835 fe200000.gpiomem: Initialised: Registers at 0xfe200000
[    1.440197] brd: module loaded
[    1.450406] loop: module loaded
[    1.451143] Loading iSCSI transport class v2.0-870.
[    1.456243] bcmgenet fd580000.ethernet: GENET 5.0 EPHY: 0x0000
[    1.562914] unimac-mdio unimac-mdio.-19: Broadcom UniMAC MDIO bus
[    1.564072] usbcore: registered new interface driver r8152
[    1.564139] usbcore: registered new interface driver lan78xx
[    1.564200] usbcore: registered new interface driver smsc95xx
[    1.565763] xhci_hcd 0000:01:00.0: enabling device (0140 -> 0142)
[    1.565935] xhci_hcd 0000:01:00.0: xHCI Host Controller
[    1.565980] xhci_hcd 0000:01:00.0: new USB bus registered, assigned bus number 1
[    1.571556] xhci_hcd 0000:01:00.0: hcc params 0x002841eb hci version 0x100 quirks 0x00003c0000000890
[    1.572586] xhci_hcd 0000:01:00.0: xHCI Host Controller
[    1.572614] xhci_hcd 0000:01:00.0: new USB bus registered, assigned bus number 2
[    1.572639] xhci_hcd 0000:01:00.0: Host supports USB 3.0 SuperSpeed
[    1.573078] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.15
[    1.573102] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    1.573121] usb usb1: Product: xHCI Host Controller
[    1.573138] usb usb1: Manufacturer: Linux 5.15.70-v7l+ xhci-hcd
[    1.573154] usb usb1: SerialNumber: 0000:01:00.0
[    1.573887] hub 1-0:1.0: USB hub found
[    1.573960] hub 1-0:1.0: 1 port detected
[    1.574966] usb usb2: New USB device found, idVendor=1d6b, idProduct=0003, bcdDevice= 5.15
[    1.574990] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    1.575009] usb usb2: Product: xHCI Host Controller
[    1.575025] usb usb2: Manufacturer: Linux 5.15.70-v7l+ xhci-hcd
[    1.575041] usb usb2: SerialNumber: 0000:01:00.0
[    1.575748] hub 2-0:1.0: USB hub found
[    1.575840] hub 2-0:1.0: 4 ports detected
[    1.577579] dwc_otg: version 3.00a 10-AUG-2012 (platform bus)
[    1.577913] dwc_otg: FIQ enabled
[    1.577927] dwc_otg: NAK holdoff enabled
[    1.577941] dwc_otg: FIQ split-transaction FSM enabled
[    1.577958] Module dwc_common_port init
[    1.578394] usbcore: registered new interface driver uas
[    1.578502] usbcore: registered new interface driver usb-storage
[    1.578696] mousedev: PS/2 mouse device common for all mice
[    1.583615] sdhci: Secure Digital Host Controller Interface driver
[    1.583632] sdhci: Copyright(c) Pierre Ossman
[    1.584298] sdhci-pltfm: SDHCI platform and OF driver helper
[    1.587857] ledtrig-cpu: registered to indicate activity on CPUs
[    1.588208] hid: raw HID events driver (C) Jiri Kosina
[    1.588388] usbcore: registered new interface driver usbhid
[    1.588403] usbhid: USB HID core driver
[    1.593515] Initializing XFRM netlink socket
[    1.593564] NET: Registered PF_PACKET protocol family
[    1.593676] Key type dns_resolver registered
[    1.594151] Registering SWP/SWPB emulation handler
[    1.594948] registered taskstats version 1
[    1.594988] Loading compiled-in X.509 certificates
[    1.595891] Key type ._fscrypt registered
[    1.595907] Key type .fscrypt registered
[    1.595922] Key type fscrypt-provisioning registered
[    1.607574] uart-pl011 fe201000.serial: there is not valid maps for state default
[    1.607885] uart-pl011 fe201000.serial: cts_event_workaround enabled
[    1.608019] fe201000.serial: ttyAMA0 at MMIO 0xfe201000 (irq = 32, base_baud = 0) is a PL011 rev2
[    1.616338] bcm2835-aux-uart fe215040.serial: there is not valid maps for state default
[    1.617090] printk: console [ttyS0] disabled
[    1.617211] fe215040.serial: ttyS0 at MMIO 0xfe215040 (irq = 34, base_baud = 62500000) is a 16550
[    1.617404] printk: console [ttyS0] enabled
[    1.618954] bcm2835-wdt bcm2835-wdt: Broadcom BCM2835 watchdog timer
[    1.619478] bcm2835-power bcm2835-power: Broadcom BCM2835 power domains driver
[    1.620752] mmc-bcm2835 fe300000.mmcnr: mmc_debug:0 mmc_debug2:0
[    1.620772] mmc-bcm2835 fe300000.mmcnr: DMA channel allocated
[    1.650052] of_cfs_init
[    1.650279] of_cfs_init: OK
[    1.686907] mmc0: SDHCI controller on fe340000.mmc [fe340000.mmc] using ADMA
[    1.687306] Waiting for root device PARTUUID=bd15ad91-02...
[    1.739928] mmc1: new high speed SDIO card at address 0001
[    1.789583] mmc0: new ultra high speed DDR50 SDXC card at address aaaa
[    1.790475] mmcblk0: mmc0:aaaa SC64G 59.5 GiB 
[    1.794994]  mmcblk0: p1 p2
[    1.795521] mmcblk0: mmc0:aaaa SC64G 59.5 GiB
[    1.817626] EXT4-fs (mmcblk0p2): mounted filesystem with ordered data mode. Opts: (null). Quota mode: none.
[    1.817709] VFS: Mounted root (ext4 filesystem) readonly on device 179:2.
[    1.821409] devtmpfs: mounted
[    1.832454] Freeing unused kernel image (initmem) memory: 2048K
[    1.853106] Run /sbin/init as init process
[    1.853122]   with arguments:
[    1.853134]     /sbin/init
[    1.853147]     splash
[    1.853160]   with environment:
[    1.853172]     HOME=/
[    1.853185]     TERM=linux
[    1.862809] usb 1-1: new high-speed USB device number 2 using xhci_hcd
[    2.055392] usb 1-1: New USB device found, idVendor=2109, idProduct=3431, bcdDevice= 4.21
[    2.055421] usb 1-1: New USB device strings: Mfr=0, Product=1, SerialNumber=0
[    2.055440] usb 1-1: Product: USB2.0 Hub
[    2.057563] hub 1-1:1.0: USB hub found
[    2.057852] hub 1-1:1.0: 4 ports detected
[    2.232986] systemd[1]: System time before build time, advancing clock.
[    2.453080] NET: Registered PF_INET6 protocol family
[    2.454718] Segment Routing with IPv6
[    2.454761] In-situ OAM (IOAM) with IPv6
[    2.533774] systemd[1]: systemd 247.3-7+rpi1 running in system mode. (+PAM +AUDIT +SELINUX +IMA +APPARMOR +SMACK +SYSVINIT +UTMP +LIBCRYPTSETUP +GCRYPT +GNUTLS +ACL +XZ +LZ4 +ZSTD +SECCOMP +BLKID +ELFUTILS +KMOD +IDN2 -IDN +PCRE2 default-hierarchy=unified)
[    2.534616] systemd[1]: Detected architecture arm.
[    2.536218] systemd[1]: Set hostname to <raspberrypi>.
[    3.242141] systemd[1]: /lib/systemd/system/plymouth-start.service:16: Unit configured to use KillMode=none. This is unsafe, as it disables systemd's process lifecycle management for the service. Please update your service to use a safer KillMode=, such as 'mixed' or 'control-group'. Support for KillMode=none is deprecated and will eventually be removed.
[    3.448198] systemd[1]: Queued start job for default target Graphical Interface.
[    3.455468] systemd[1]: Created slice system-getty.slice.
[    3.456841] systemd[1]: Created slice system-modprobe.slice.
[    3.457844] systemd[1]: Created slice system-serial\x2dgetty.slice.
[    3.458811] systemd[1]: Created slice system-systemd\x2dfsck.slice.
[    3.459637] systemd[1]: Created slice User and Session Slice.
[    3.460179] systemd[1]: Started Forward Password Requests to Wall Directory Watch.
[    3.461242] systemd[1]: Set up automount Arbitrary Executable File Formats File System Automount Point.
[    3.461998] systemd[1]: Reached target Slices.
[    3.462173] systemd[1]: Reached target Swap.
[    3.463505] systemd[1]: Listening on Syslog Socket.
[    3.464277] systemd[1]: Listening on fsck to fsckd communication Socket.
[    3.464723] systemd[1]: Listening on initctl Compatibility Named Pipe.
[    3.465797] systemd[1]: Listening on Journal Audit Socket.
[    3.466623] systemd[1]: Listening on Journal Socket (/dev/log).
[    3.467582] systemd[1]: Listening on Journal Socket.
[    3.475664] systemd[1]: Listening on udev Control Socket.
[    3.476609] systemd[1]: Listening on udev Kernel Socket.
[    3.477504] systemd[1]: Condition check resulted in Huge Pages File System being skipped.
[    3.482900] systemd[1]: Mounting POSIX Message Queue File System...
[    3.489235] systemd[1]: Mounting RPC Pipe File System...
[    3.495984] systemd[1]: Mounting Kernel Debug File System...
[    3.503261] systemd[1]: Mounting Kernel Trace File System...
[    3.504122] systemd[1]: Condition check resulted in Kernel Module supporting RPCSEC_GSS being skipped.
[    3.517562] systemd[1]: Starting Restore / save the current clock...
[    3.524890] systemd[1]: Starting Set the console keyboard layout...
[    3.532687] systemd[1]: Starting Create list of static device nodes for the current kernel...
[    3.540563] systemd[1]: Starting Load Kernel Module configfs...
[    3.548443] systemd[1]: Starting Load Kernel Module drm...
[    3.555857] systemd[1]: Starting Load Kernel Module fuse...
[    3.560746] systemd[1]: Condition check resulted in Set Up Additional Binary Formats being skipped.
[    3.567852] systemd[1]: Starting File System Check on Root Device...
[    3.581195] systemd[1]: Starting Journal Service...
[    3.599076] systemd[1]: Starting Load Kernel Modules...
[    3.606168] systemd[1]: Starting Coldplug All udev Devices...
[    3.631307] systemd[1]: Mounted POSIX Message Queue File System.
[    3.631988] systemd[1]: Mounted RPC Pipe File System.
[    3.632619] systemd[1]: Mounted Kernel Debug File System.
[    3.638385] systemd[1]: Mounted Kernel Trace File System.
[    3.643174] systemd[1]: Finished Restore / save the current clock.
[    3.655154] fuse: init (API version 7.34)
[    3.658594] systemd[1]: Finished Create list of static device nodes for the current kernel.
[    3.660832] systemd[1]: modprobe@configfs.service: Succeeded.
[    3.662486] systemd[1]: Finished Load Kernel Module configfs.
[    3.671228] systemd[1]: modprobe@fuse.service: Succeeded.
[    3.672827] systemd[1]: Finished Load Kernel Module fuse.
[    3.681662] systemd[1]: Mounting FUSE Control File System...
[    3.689466] systemd[1]: Mounting Kernel Configuration File System...
[    3.696180] systemd[1]: Started File System Check Daemon to report status.
[    3.722903] i2c_dev: i2c /dev entries driver
[    3.732800] systemd[1]: Finished Load Kernel Modules.
[    3.771061] systemd[1]: Starting Apply Kernel Variables...
[    3.793640] systemd[1]: Mounted FUSE Control File System.
[    3.801302] systemd[1]: Mounted Kernel Configuration File System.
[    3.841513] systemd[1]: Finished Apply Kernel Variables.
[    3.865054] systemd[1]: modprobe@drm.service: Succeeded.
[    3.866509] systemd[1]: Finished Load Kernel Module drm.
[    3.944652] systemd[1]: Finished File System Check on Root Device.
[    3.950174] systemd[1]: Starting Remount Root and Kernel File Systems...
[    3.976946] systemd[1]: Started Journal Service.
[    4.120370] EXT4-fs (mmcblk0p2): re-mounted. Opts: (null). Quota mode: none.
[    4.193139] systemd-journald[136]: Received client request to flush runtime journal.
[    4.223610] systemd-journald[136]: File /var/log/journal/65b48c2d72684a708cb845df3c60558d/system.journal corrupted or uncleanly shut down, renaming and replacing.
[    5.495369] mc: Linux media interface: v0.10
[    5.587670] vc_sm_cma: module is from the staging directory, the quality is unknown, you have been warned.
[    5.653592] videodev: Linux video capture interface: v2.00
[    5.686455] bcm2835_vc_sm_cma_probe: Videocore shared memory driver
[    5.686530] [vc_sm_connected_init]: start
[    5.763144] [vc_sm_connected_init]: installed successfully
[    5.795222] rpivid_hevc: module is from the staging directory, the quality is unknown, you have been warned.
[    5.864270] rpivid feb10000.codec: Device registered as /dev/video19
[    5.877947] bcm2835_mmal_vchiq: module is from the staging directory, the quality is unknown, you have been warned.
[    5.916946] bcm2835_mmal_vchiq: module is from the staging directory, the quality is unknown, you have been warned.
[    5.963440] bcm2835_v4l2: module is from the staging directory, the quality is unknown, you have been warned.
[    5.968353] bcm2835_isp: module is from the staging directory, the quality is unknown, you have been warned.
[    6.006422] bcm2835_codec: module is from the staging directory, the quality is unknown, you have been warned.
[    6.324670] bcm2835-isp bcm2835-isp: Device node output[0] registered as /dev/video13
[    6.325594] bcm2835-codec bcm2835-codec: Device registered as /dev/video10
[    6.325646] bcm2835-codec bcm2835-codec: Loaded V4L2 decode
[    6.325909] bcm2835-isp bcm2835-isp: Device node capture[0] registered as /dev/video14
[    6.326908] bcm2835-isp bcm2835-isp: Device node capture[1] registered as /dev/video15
[    6.327543] bcm2835-isp bcm2835-isp: Device node stats[2] registered as /dev/video16
[    6.327581] bcm2835-isp bcm2835-isp: Register output node 0 with media controller
[    6.327612] bcm2835-isp bcm2835-isp: Register capture node 1 with media controller
[    6.327651] bcm2835-isp bcm2835-isp: Register capture node 2 with media controller
[    6.327674] bcm2835-isp bcm2835-isp: Register capture node 3 with media controller
[    6.351793] bcm2835-isp bcm2835-isp: Device node output[0] registered as /dev/video20
[    6.352525] bcm2835-isp bcm2835-isp: Device node capture[0] registered as /dev/video21
[    6.359014] bcm2835-isp bcm2835-isp: Device node capture[1] registered as /dev/video22
[    6.363868] bcm2835-codec bcm2835-codec: Device registered as /dev/video11
[    6.363936] bcm2835-codec bcm2835-codec: Loaded V4L2 encode
[    6.364184] bcm2835-isp bcm2835-isp: Device node stats[2] registered as /dev/video23
[    6.364213] bcm2835-isp bcm2835-isp: Register output node 0 with media controller
[    6.364238] bcm2835-isp bcm2835-isp: Register capture node 1 with media controller
[    6.364261] bcm2835-isp bcm2835-isp: Register capture node 2 with media controller
[    6.364283] bcm2835-isp bcm2835-isp: Register capture node 3 with media controller
[    6.375139] bcm2835-codec bcm2835-codec: Device registered as /dev/video12
[    6.375186] bcm2835-codec bcm2835-codec: Loaded V4L2 isp
[    6.404474] bcm2835-codec bcm2835-codec: Device registered as /dev/video18
[    6.404522] bcm2835-codec bcm2835-codec: Loaded V4L2 image_fx
[    6.428622] [drm] Initialized v3d 1.0.0 20180419 for fec00000.v3d on minor 0
[    6.432850] bcm2835-isp bcm2835-isp: Loaded V4L2 bcm2835-isp
[    6.434395] bcm2835-codec bcm2835-codec: Device registered as /dev/video31
[    6.434461] bcm2835-codec bcm2835-codec: Loaded V4L2 encode_image
[    6.562036] cfg80211: Loading compiled-in X.509 certificates for regulatory database
[    6.634183] cfg80211: Loaded X.509 cert 'sforshee: 00b28ddf47aef9cea7'
[    6.664460] cfg80211: loaded regulatory.db is malformed or signature is missing/invalid
[    6.980628] brcmfmac: F1 signature read @0x18000000=0x15264345
[    7.048753] [drm] No displays found. Consider forcing hotplug if HDMI is attached
[    7.048782] vc4-drm gpu: bound fe600000.firmwarekms (ops vc4_fkms_ops [vc4])
[    7.050619] brcmfmac: brcmf_fw_alloc_request: using brcm/brcmfmac43455-sdio for chip BCM4345/6
[    7.051487] [drm] Initialized vc4 0.0.0 20140616 for gpu on minor 1
[    7.052262] usbcore: registered new interface driver brcmfmac
[    7.058975] brcmfmac mmc1:0001:1: Direct firmware load for brcm/brcmfmac43455-sdio.raspberrypi,4-model-b.bin failed with error -2
[    7.331576] brcmfmac: brcmf_fw_alloc_request: using brcm/brcmfmac43455-sdio for chip BCM4345/6
[    7.331756] brcmfmac: brcmf_fw_alloc_request: using brcm/brcmfmac43455-sdio for chip BCM4345/6
[    7.348704] brcmfmac: brcmf_c_preinit_dcmds: Firmware: BCM4345/6 wl0: Nov  1 2021 00:37:25 version 7.45.241 (1a2f2fa CY) FWID 01-703fd60
[    7.833988] uart-pl011 fe201000.serial: no DMA platform data
[    7.937755] 8021q: 802.1Q VLAN Support v1.8
[    8.117273] Adding 1048572k swap on /var/swap.  Priority:-2 extents:1 across:1048572k SSFS
[    8.496905] brcmfmac: brcmf_cfg80211_set_power_mgmt: power save enabled
[    8.832183] bcmgenet fd580000.ethernet: configuring instance for external RGMII (RX delay)
[    8.833180] bcmgenet fd580000.ethernet eth0: Link is Down
[   14.482663] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[   14.665096] Bluetooth: Core ver 2.22
[   14.665161] NET: Registered PF_BLUETOOTH protocol family
[   14.665168] Bluetooth: HCI device and connection manager initialized
[   14.665182] Bluetooth: HCI socket layer initialized
[   14.665193] Bluetooth: L2CAP socket layer initialized
[   14.665209] Bluetooth: SCO socket layer initialized
[   14.675542] Bluetooth: HCI UART driver ver 2.3
[   14.675559] Bluetooth: HCI UART protocol H4 registered
[   14.675618] Bluetooth: HCI UART protocol Three-wire (H5) registered
[   14.675786] Bluetooth: HCI UART protocol Broadcom registered
[   14.915015] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
[   14.915030] Bluetooth: BNEP filters: protocol multicast
[   14.915044] Bluetooth: BNEP socket layer initialized
[   14.936731] NET: Registered PF_ALG protocol family
[   14.968513] cryptd: max_cpu_qlen set to 1000
[   15.705622] ICMPv6: process `dhcpcd' is using deprecated sysctl (syscall) net.ipv6.neigh.wlan0.retrans_time - use net.ipv6.neigh.wlan0.retrans_time_ms instead
[   31.832692] cam-dummy-reg: disabling
rpi@raspberrypi:~ $ sudo vcdbg log msg
005349.782: arasan: arasan_emmc_open
005788.328: brfs: File read: /mfs/sd/config.txt
005789.343: brfs: File read: 2164 bytes
005810.891: HDMI0:EDID error reading EDID block 0 attempt 0
005811.906: HDMI0:EDID giving up on reading EDID block 0
005823.595: HDMI1:EDID error reading EDID block 0 attempt 0
005824.611: HDMI1:EDID giving up on reading EDID block 0
005828.001: brfs: File read: /mfs/sd/config.txt
006277.748: gpioman: gpioman_get_pin_num: pin DISPLAY_DSI_PORT not defined
006280.267: *** Restart logging
006280.288: brfs: File read: 2164 bytes
006285.819: hdmi: HDMI0:EDID error reading EDID block 0 attempt 0
006286.837: hdmi: HDMI0:EDID giving up on reading EDID block 0
006291.878: hdmi: HDMI0:EDID error reading EDID block 0 attempt 0
006292.894: hdmi: HDMI0:EDID giving up on reading EDID block 0
006292.912: hdmi: HDMI:hdmi_get_state is deprecated, use hdmi_get_display_state instead
006297.954: hdmi: HDMI1:EDID error reading EDID block 0 attempt 0
006298.968: hdmi: HDMI1:EDID giving up on reading EDID block 0
006304.010: hdmi: HDMI1:EDID error reading EDID block 0 attempt 0
006305.027: hdmi: HDMI1:EDID giving up on reading EDID block 0
006305.042: hdmi: HDMI:hdmi_get_state is deprecated, use hdmi_get_display_state instead
006305.056: HDMI0: hdmi_pixel_encoding: 300000000
006305.070: HDMI1: hdmi_pixel_encoding: 300000000
006306.184: dtb_file 'bcm2711-rpi-4-b.dtb'
006306.196: Trying Device Tree file 'bcm2711-rpi-4-b.dtb'
006313.607: brfs: File read: /mfs/sd/bcm2711-rpi-4-b.dtb
006313.622: Loaded 'bcm2711-rpi-4-b.dtb' to 0x100 size 0xcb54
006323.607: dtdebug: delete_node(/__local_fixups__)
006326.629: brfs: File read: 52052 bytes
006340.030: dtdebug: using platform 'bcm2711'
006341.081: brfs: File read: /mfs/sd/overlays/overlay_map.dtb
006342.157: dtdebug: overlay map loaded
006343.546: dtdebug: /aliases:i2c_vc=i2c0
006348.528: dtdebug: /__symbols__:i2c_vc=i2c0
006351.998: dtdebug: /__overrides__:i2c_vc=i2c0
006359.114: dtdebug: /__overrides__:i2c_vc_baudrate=i2c0_baudrate
006360.455: dtdebug: /aliases:i2c=i2c1
006365.484: dtdebug: /__symbols__:i2c=i2c1
006368.985: dtdebug: /__overrides__:i2c=i2c1
006370.336: dtdebug: /aliases:i2c_arm=i2c1
006375.382: dtdebug: /__symbols__:i2c_arm=i2c1
006378.888: dtdebug: /__overrides__:i2c_arm=i2c1
006386.044: dtdebug: /__overrides__:i2c_baudrate=i2c1_baudrate
006393.208: dtdebug: /__overrides__:i2c_arm_baudrate=i2c1_baudrate
006410.531: dtparam: uart0_clkrate=48000000
006413.415: dtdebug: /__overrides__ has no uart0_clkrate property
006413.424: Unknown dtparam 'uart0_clkrate' - ignored
006413.442: brfs: File read: 2231 bytes
006417.571: brfs: File read: /mfs/sd/config.txt
006417.950: dtparam: i2c_arm=on
006420.743: dtdebug: found override i2c_arm
006420.769: dtdebug:   override i2c_arm: string target 'status'
006426.731: dtparam: spi=on
006429.538: dtdebug: found override spi
006429.561: dtdebug:   override spi: string target 'status'
006435.383: brfs: File read: 2164 bytes
006441.562: dtdebug: Opened overlay file 'overlays/hifiberry-dacplus.dtbo'
006442.661: brfs: File read: /mfs/sd/overlays/hifiberry-dacplus.dtbo
006458.809: Loaded overlay 'hifiberry-dacplus'
006461.001: dtdebug: merge_fragment(/,/fragment@0/__overlay__)
006467.915: dtdebug: merge_fragment(/dacpro_osc,/fragment@0/__overlay__/dacpro_osc)
006467.932: dtdebug:   +prop(compatible)
006468.715: dtdebug:   +prop(#clock-cells)
006469.534: dtdebug:   +prop(phandle)
006470.343: dtdebug: merge_fragment() end
006470.360: dtdebug: merge_fragment() end
006477.341: dtdebug: merge_fragment(/soc/i2s@7e203000,/fragment@1/__overlay__)
006477.359: dtdebug:   +prop(status)
006477.897: dtdebug: merge_fragment() end
006485.859: dtdebug: merge_fragment(/soc/i2c@7e804000,/fragment@2/__overlay__)
006485.876: dtdebug:   +prop(#address-cells)
006486.359: dtdebug:   +prop(#size-cells)
006486.843: dtdebug:   +prop(status)
006490.395: dtdebug: merge_fragment(/soc/i2c@7e804000/pcm5122@4d,/fragment@2/__overlay__/pcm5122@4d)
006490.412: dtdebug:   +prop(#sound-dai-cells)
006490.933: dtdebug:   +prop(compatible)
006491.409: dtdebug:   +prop(reg)
006491.909: dtdebug:   +prop(clocks)
006492.416: dtdebug:   +prop(AVDD-supply)
006493.138: dtdebug:   +prop(DVDD-supply)
006493.867: dtdebug:   +prop(CPVDD-supply)
006494.597: dtdebug:   +prop(status)
006495.118: dtdebug: merge_fragment() end
006498.251: dtdebug: merge_fragment(/soc/i2c@7e804000/hpamp@60,/fragment@2/__overlay__/hpamp@60)
006498.268: dtdebug:   +prop(compatible)
006498.744: dtdebug:   +prop(reg)
006499.243: dtdebug:   +prop(status)
006499.744: dtdebug:   +prop(phandle)
006500.248: dtdebug: merge_fragment() end
006500.265: dtdebug: merge_fragment() end
006510.808: dtdebug: merge_fragment(/soc/sound,/fragment@3/__overlay__)
006510.825: dtdebug:   +prop(compatible)
006511.165: dtdebug:   +prop(i2s-controller)
006511.752: dtdebug:   +prop(status)
006512.091: dtdebug: merge_fragment() end
006512.606: dtdebug: mapped overlay 'vc4-fkms-v3d' to 'vc4-fkms-v3d-pi4'
006512.626: brfs: File read: 1916 bytes
006527.424: dtdebug: Opened overlay file 'overlays/vc4-fkms-v3d-pi4.dtbo'
006528.557: brfs: File read: /mfs/sd/overlays/vc4-fkms-v3d-pi4.dtbo
006546.277: Loaded overlay 'vc4-fkms-v3d'
006546.288: dtparam: audio=off
006546.360: dtdebug: /__overrides__ has no audio property
006549.257: dtdebug: found override audio
006549.280: dtdebug:   override audio: string target 'status'
006559.888: dtdebug: merge_fragment(/reserved-memory/linux,cma,/fragment@0/__overlay__)
006559.904: dtdebug:   +prop(size)
006560.682: dtdebug: merge_fragment() end
006571.160: dtdebug: merge_fragment(/soc/fb,/fragment@1/__overlay__)
006571.174: dtdebug:   +prop(status)
006571.516: dtdebug: merge_fragment() end
006581.764: dtdebug: merge_fragment(/soc/firmwarekms@7e600000,/fragment@2/__overlay__)
006581.781: dtdebug:   +prop(status)
006582.150: dtdebug: merge_fragment() end
006594.812: dtdebug: merge_fragment(/v3dbus/v3d@7ec04000,/fragment@3/__overlay__)
006594.826: dtdebug:   +prop(status)
006595.075: dtdebug: merge_fragment() end
006605.758: dtdebug: merge_fragment(/gpu,/fragment@4/__overlay__)
006605.774: dtdebug:   +prop(status)
006606.107: dtdebug: merge_fragment() end
006612.122: brfs: File read: 1446 bytes
006615.866: brfs: File read: /mfs/sd/cmdline.txt
006615.913: Read command line from file 'cmdline.txt':
006615.928: 'console=serial0,115200 console=tty1 root=PARTUUID=bd15ad91-02 rootfstype=ext4 fsck.repair=yes rootwait quiet splash plymouth.ignore-serial-consoles'
006825.170: dtparam: cam0-pwdn-ctrl=11
006827.997: dtdebug: found override cam0-pwdn-ctrl
006828.012: dtparam: cam0-pwdn=5
006830.841: dtdebug: found override cam0-pwdn
006830.862: dtparam: arm_freq=1500000000
006833.755: dtdebug: found override arm_freq
006833.772: dtparam: core_freq=500000000
006836.714: dtdebug: /__overrides__ has no core_freq property
006836.725: Unknown dtparam 'core_freq' - ignored
006845.851: dtdebug: delete_node(/hat)
006851.877: kernel=
006851.895: brfs: File read: 148 bytes
007460.776: brfs: File read: /mfs/sd/kernel7l.img
007460.795: Loaded 'kernel7l.img' to 0x8000 size 0x6b6e58
007460.827: Device tree loaded to 0x2eff2d00 (size 0xd2cd)
007481.222: gpioman: gpioman_get_pin_num: pin SDCARD_CONTROL_POWER not defined
010857.292: vchiq_core: vchiq_init_state: slot_zero = 0xdad80000, is_master = 1
015252.150: camsubs: Looking for camera 0: i2c_port = 0, led gpio = -1, power enable gpio = 133
015551.279: camsubs: Camera not found
015551.353: camsubs: Looking for camera 0: i2c_port = 0, led gpio = -1, power enable gpio = 133
015559.655: camsubs: Camera not found
015559.715: camsubs: Looking for camera 0: i2c_port = 0, led gpio = -1, power enable gpio = 133
015567.882: camsubs: Camera not found
015567.941: camsubs: Looking for camera 0: i2c_port = 0, led gpio = -1, power enable gpio = 133
015569.418: camsubs: Camera not found
015569.478: camsubs: Looking for camera 0: i2c_port = 0, led gpio = -1, power enable gpio = 133
015579.151: camsubs: Camera not found

sudo vcdbg log msg
005349.782: arasan: arasan_emmc_open
005788.328: brfs: File read: /mfs/sd/config.txt
005789.343: brfs: File read: 2164 bytes
005810.891: HDMI0:EDID error reading EDID block 0 attempt 0
005811.906: HDMI0:EDID giving up on reading EDID block 0
005823.595: HDMI1:EDID error reading EDID block 0 attempt 0
005824.611: HDMI1:EDID giving up on reading EDID block 0
005828.001: brfs: File read: /mfs/sd/config.txt
006277.748: gpioman: gpioman_get_pin_num: pin DISPLAY_DSI_PORT not defined
006280.267: *** Restart logging
006280.288: brfs: File read: 2164 bytes
006285.819: hdmi: HDMI0:EDID error reading EDID block 0 attempt 0
006286.837: hdmi: HDMI0:EDID giving up on reading EDID block 0
006291.878: hdmi: HDMI0:EDID error reading EDID block 0 attempt 0
006292.894: hdmi: HDMI0:EDID giving up on reading EDID block 0
006292.912: hdmi: HDMI:hdmi_get_state is deprecated, use hdmi_get_display_state instead
006297.954: hdmi: HDMI1:EDID error reading EDID block 0 attempt 0
006298.968: hdmi: HDMI1:EDID giving up on reading EDID block 0
006304.010: hdmi: HDMI1:EDID error reading EDID block 0 attempt 0
006305.027: hdmi: HDMI1:EDID giving up on reading EDID block 0
006305.042: hdmi: HDMI:hdmi_get_state is deprecated, use hdmi_get_display_state instead
006305.056: HDMI0: hdmi_pixel_encoding: 300000000
006305.070: HDMI1: hdmi_pixel_encoding: 300000000
006306.184: dtb_file 'bcm2711-rpi-4-b.dtb'
006306.196: Trying Device Tree file 'bcm2711-rpi-4-b.dtb'
006313.607: brfs: File read: /mfs/sd/bcm2711-rpi-4-b.dtb
006313.622: Loaded 'bcm2711-rpi-4-b.dtb' to 0x100 size 0xcb54
006323.607: dtdebug: delete_node(/__local_fixups__)
006326.629: brfs: File read: 52052 bytes
006340.030: dtdebug: using platform 'bcm2711'
006341.081: brfs: File read: /mfs/sd/overlays/overlay_map.dtb
006342.157: dtdebug: overlay map loaded
006343.546: dtdebug: /aliases:i2c_vc=i2c0
006348.528: dtdebug: /__symbols__:i2c_vc=i2c0
006351.998: dtdebug: /__overrides__:i2c_vc=i2c0
006359.114: dtdebug: /__overrides__:i2c_vc_baudrate=i2c0_baudrate
006360.455: dtdebug: /aliases:i2c=i2c1
006365.484: dtdebug: /__symbols__:i2c=i2c1
006368.985: dtdebug: /__overrides__:i2c=i2c1
006370.336: dtdebug: /aliases:i2c_arm=i2c1
006375.382: dtdebug: /__symbols__:i2c_arm=i2c1
006378.888: dtdebug: /__overrides__:i2c_arm=i2c1
006386.044: dtdebug: /__overrides__:i2c_baudrate=i2c1_baudrate
006393.208: dtdebug: /__overrides__:i2c_arm_baudrate=i2c1_baudrate
006410.531: dtparam: uart0_clkrate=48000000
006413.415: dtdebug: /__overrides__ has no uart0_clkrate property
006413.424: Unknown dtparam 'uart0_clkrate' - ignored
006413.442: brfs: File read: 2231 bytes
006417.571: brfs: File read: /mfs/sd/config.txt
006417.950: dtparam: i2c_arm=on
006420.743: dtdebug: found override i2c_arm
006420.769: dtdebug:   override i2c_arm: string target 'status'
006426.731: dtparam: spi=on
006429.538: dtdebug: found override spi
006429.561: dtdebug:   override spi: string target 'status'
006435.383: brfs: File read: 2164 bytes
006441.562: dtdebug: Opened overlay file 'overlays/hifiberry-dacplus.dtbo'
006442.661: brfs: File read: /mfs/sd/overlays/hifiberry-dacplus.dtbo
006458.809: Loaded overlay 'hifiberry-dacplus'
006461.001: dtdebug: merge_fragment(/,/fragment@0/__overlay__)
006467.915: dtdebug: merge_fragment(/dacpro_osc,/fragment@0/__overlay__/dacpro_osc)
006467.932: dtdebug:   +prop(compatible)
006468.715: dtdebug:   +prop(#clock-cells)
006469.534: dtdebug:   +prop(phandle)
006470.343: dtdebug: merge_fragment() end
006470.360: dtdebug: merge_fragment() end
006477.341: dtdebug: merge_fragment(/soc/i2s@7e203000,/fragment@1/__overlay__)
006477.359: dtdebug:   +prop(status)
006477.897: dtdebug: merge_fragment() end
006485.859: dtdebug: merge_fragment(/soc/i2c@7e804000,/fragment@2/__overlay__)
006485.876: dtdebug:   +prop(#address-cells)
006486.359: dtdebug:   +prop(#size-cells)
006486.843: dtdebug:   +prop(status)
006490.395: dtdebug: merge_fragment(/soc/i2c@7e804000/pcm5122@4d,/fragment@2/__overlay__/pcm5122@4d)
006490.412: dtdebug:   +prop(#sound-dai-cells)
006490.933: dtdebug:   +prop(compatible)
006491.409: dtdebug:   +prop(reg)
006491.909: dtdebug:   +prop(clocks)
006492.416: dtdebug:   +prop(AVDD-supply)
006493.138: dtdebug:   +prop(DVDD-supply)
006493.867: dtdebug:   +prop(CPVDD-supply)
006494.597: dtdebug:   +prop(status)
006495.118: dtdebug: merge_fragment() end
006498.251: dtdebug: merge_fragment(/soc/i2c@7e804000/hpamp@60,/fragment@2/__overlay__/hpamp@60)
006498.268: dtdebug:   +prop(compatible)
006498.744: dtdebug:   +prop(reg)
006499.243: dtdebug:   +prop(status)
006499.744: dtdebug:   +prop(phandle)
006500.248: dtdebug: merge_fragment() end
006500.265: dtdebug: merge_fragment() end
006510.808: dtdebug: merge_fragment(/soc/sound,/fragment@3/__overlay__)
006510.825: dtdebug:   +prop(compatible)
006511.165: dtdebug:   +prop(i2s-controller)
006511.752: dtdebug:   +prop(status)
006512.091: dtdebug: merge_fragment() end
006512.606: dtdebug: mapped overlay 'vc4-fkms-v3d' to 'vc4-fkms-v3d-pi4'
006512.626: brfs: File read: 1916 bytes
006527.424: dtdebug: Opened overlay file 'overlays/vc4-fkms-v3d-pi4.dtbo'
006528.557: brfs: File read: /mfs/sd/overlays/vc4-fkms-v3d-pi4.dtbo
006546.277: Loaded overlay 'vc4-fkms-v3d'
006546.288: dtparam: audio=off
006546.360: dtdebug: /__overrides__ has no audio property
006549.257: dtdebug: found override audio
006549.280: dtdebug:   override audio: string target 'status'
006559.888: dtdebug: merge_fragment(/reserved-memory/linux,cma,/fragment@0/__overlay__)
006559.904: dtdebug:   +prop(size)
006560.682: dtdebug: merge_fragment() end
006571.160: dtdebug: merge_fragment(/soc/fb,/fragment@1/__overlay__)
006571.174: dtdebug:   +prop(status)
006571.516: dtdebug: merge_fragment() end
006581.764: dtdebug: merge_fragment(/soc/firmwarekms@7e600000,/fragment@2/__overlay__)
006581.781: dtdebug:   +prop(status)
006582.150: dtdebug: merge_fragment() end
006594.812: dtdebug: merge_fragment(/v3dbus/v3d@7ec04000,/fragment@3/__overlay__)
006594.826: dtdebug:   +prop(status)
006595.075: dtdebug: merge_fragment() end
006605.758: dtdebug: merge_fragment(/gpu,/fragment@4/__overlay__)
006605.774: dtdebug:   +prop(status)
006606.107: dtdebug: merge_fragment() end
006612.122: brfs: File read: 1446 bytes
006615.866: brfs: File read: /mfs/sd/cmdline.txt
006615.913: Read command line from file 'cmdline.txt':
006615.928: 'console=serial0,115200 console=tty1 root=PARTUUID=bd15ad91-02 rootfstype=ext4 fsck.repair=yes rootwait quiet splash plymouth.ignore-serial-consoles'
006825.170: dtparam: cam0-pwdn-ctrl=11
006827.997: dtdebug: found override cam0-pwdn-ctrl
006828.012: dtparam: cam0-pwdn=5
006830.841: dtdebug: found override cam0-pwdn
006830.862: dtparam: arm_freq=1500000000
006833.755: dtdebug: found override arm_freq
006833.772: dtparam: core_freq=500000000
006836.714: dtdebug: /__overrides__ has no core_freq property
006836.725: Unknown dtparam 'core_freq' - ignored
006845.851: dtdebug: delete_node(/hat)
006851.877: kernel=
006851.895: brfs: File read: 148 bytes
007460.776: brfs: File read: /mfs/sd/kernel7l.img
007460.795: Loaded 'kernel7l.img' to 0x8000 size 0x6b6e58
007460.827: Device tree loaded to 0x2eff2d00 (size 0xd2cd)
007481.222: gpioman: gpioman_get_pin_num: pin SDCARD_CONTROL_POWER not defined
010857.292: vchiq_core: vchiq_init_state: slot_zero = 0xdad80000, is_master = 1
015252.150: camsubs: Looking for camera 0: i2c_port = 0, led gpio = -1, power enable gpio = 133
015551.279: camsubs: Camera not found
015551.353: camsubs: Looking for camera 0: i2c_port = 0, led gpio = -1, power enable gpio = 133
015559.655: camsubs: Camera not found
015559.715: camsubs: Looking for camera 0: i2c_port = 0, led gpio = -1, power enable gpio = 133
015567.882: camsubs: Camera not found
015567.941: camsubs: Looking for camera 0: i2c_port = 0, led gpio = -1, power enable gpio = 133
015569.418: camsubs: Camera not found
015569.478: camsubs: Looking for camera 0: i2c_port = 0, led gpio = -1, power enable gpio = 133
015579.151: camsubs: Camera not found

2 comments

Please sign in to leave a comment.