0

I'm LOST please Help

Raspix

November 27, 2018 13:43

None

Follow

Hello,

I cannot hear anything at the Output of Sound Card : nothing is audible on the speakers.

I will be particularily grateful if you could help me !!

 

First of all, here is a view of my card :

https://www.hifiberry.com/blog/introducing-the-amp2-more-power-higher-sample-rates-more-affordable/

Here are the configurations :

HERE IS MY  config.txt FILE :

hdmi_drive=0

dtparam=audio=on

uncomment to increase signal to HDMI, if you have interference, blanking, or

no display

#config_hdmi_boost=4

uncomment for composite PAL

#sdtv_mode=2

#uncomment to overclock the arm. 700 MHz is the default.

#arm_freq=800

Uncomment some or all of these to enable the optional hardware interfaces

dtoverlay=hifiberry-amp

dtdebug=1

#dtparam=i2c_arm=on

#dtparam=i2s=on

#dtparam=spi=on

Uncomment this to enable the lirc-rpi module

#dtoverlay=lirc-rpi

Additional overlays and parameters are documented /boot/overlays/README

Enable audio (loads snd_bcm2835)

start_x=1

gpu_mem=128

enable_uart=1

dtoverlay=w1-gpio

---> menu Advanced/son : auto

 

 

$ sudo aplay -l
aplay: device_list:270: None Sound card has been found
$

 

 

THANKS IN ADVANCE !!!!!!!!!

• Facebook
• Twitter
• LinkedIn

12 comments

• 0
  
  HiFiBerry team December 15, 2018 16:43

  Hi,

  you're using the wrong module. For the Amp2, you have to use the hifiverry-dacplus overlay.

  Best regards;
  Daniel

• 0
  
  Raspix December 16, 2018 09:04

  Ah Yes !! Thanks for answering me :)

  I will retry it but I'm going from memory, I think I've already tested to modify my config file as adviced with the following parameter :

  dtoverlay=hifiberry-dacplus overlay

  Is that the new test to be tested ?

  Correct me if I'm wrong.

   

  Thanks a lot

• 0
  
  HiFiBerry team December 16, 2018 10:58

  Yes, that's correct. It should work with these setting.

• 0
  
  Raspix December 22, 2018 17:54

  Hello Thanks again for the answer.

  I modified the file, but it didn't work.

  I can't hear anything after the modification :(

• 0
  
  Raspix December 23, 2018 20:56

  
  
  
  
  
  
  
  
  

• 0
  
  Raspix December 23, 2018 20:57

  
  
  
  
  
  
  
  
  

• 0
  
  Raspix December 23, 2018 20:58

  In my previous comment you will find the VLC audio menu and also my complete config file.

   

  Still don't work :( ..

   

  The next comment will provide the end of the config file

  I didn't hear anything when I try to launch a local mp3 file through VLC. See audio menus.

  Edited by Raspix December 23, 2018 21:01
• 0
  
  Raspix December 23, 2018 20:59

  

• 0
  
  HiFiBerry team December 24, 2018 09:16

  First, check that the card is configured correctly using

  aplay -l

  It also looks like you have PulseAudio running. As the PulseAudio configuration is very complex, this often creates problem. We recommend NOT to use the Raspbian GUI, but distributions specifically designed for audio playback.

  Best regards,
  Daniel

• 0
  
  Raspix December 28, 2018 14:59

  Hello Daniel,

  I've just seen your last comment that seems to be close to truth unfortunately.....here is the requested command :

   

  pi@raspberrypi:/boot $ aplay -l

  aplay: device_list:270: aucune carte son n’a été trouvée... /// english translation : No Sound Card has been detected

   

  I'm upset and don't understand why such an issue why the Analogic Standard Car speaker cannot play anything :( :( :(

• 0
  
  HiFiBerry team December 28, 2018 16:18

  Ok, this looks like the card isn't configured at all. What distribution are you using?

   

  Best regards,
  Daniel

• 0
  
  Raspix December 28, 2018 20:31

  --> its name is JESSY