0

Digi+ doesn't work on my RPI2 OpenELEC

Yaron Zamir

August 15, 2015 03:14

None

Follow

Hi.

I am trying to configure my new Digi+ card to work in OpenELEC v5.95.3 on a RPI2, with no success.
Following the configuration for OpenELEC v5.02 using device-tree-overlays, the card is not shown in the
Kodi settings for Audio options.

Going over some threads in this forum (which i found to be most educating), i tried to start with
a new installation of OpenELEC, but got the same results, no sound, and the card is not recognized.

Here are some log output:

aplay dmesg lsmod:

OpenELEC-Basement:~ # aplay -l
aplay: device_list:268: no soundcards found...


OpenELEC-Basement:~ # dmesg | grep -i hifiberry
[ 4.925260] snd-hifiberry-digi sound: ASoC: CPU DAI (null) not registered
[ 4.925299] snd-hifiberry-digi sound: snd_soc_register_card() failed: -517
[ 4.945390] snd-hifiberry-digi sound: ASoC: CODEC DAI wm8804-spdif not registered
[ 4.945420] snd-hifiberry-digi sound: snd_soc_register_card() failed: -517


OpenELEC-Basement:~ # lsmod
Module Size Used by
snd_soc_bcm2708_i2s 6023 0
regmap_mmio 2050 1 snd_soc_bcm2708_i2s
snd_soc_hifiberry_digi 2811 0
snd_soc_core 102814 2 snd_soc_hifiberry_digi,snd_soc_bcm2708_i2s
snd_compress 7024 1 snd_soc_core
snd_pcm_dmaengine 2731 1 snd_soc_core
snd_pcm 61496 2 snd_soc_core,snd_pcm_dmaengine
snd_timer 16593 1 snd_pcm
snd 39964 4 snd_soc_core,snd_timer,snd_pcm,snd_compress
bcm2708_rng 821 0

vcdbg log msg

OpenELEC-Basement:~ # vcdbg log msg
001120.837: HDMI:EDID version 1.3, 1 extensions, screen size 112x63 cm
001120.902: HDMI:EDID features - videodef 0x80 !standby !suspend !active off; colour encoding:RGB444|YCbCr422; sRGB is not default colourspace; preferred format is native; does not support GTF
001120.959: HDMI:EDID found preferred CEA detail timing format: 1920x1080p @ 60 Hz (16)
001121.022: HDMI:EDID found DMT detail timing format: 1360x768p @ 60 Hz (39)
001121.063: HDMI:EDID found DMT format: code 4, 640x480p @ 60 Hz in established timing I/II
001121.102: HDMI:EDID found DMT format: code 5, 640x480p @ 72 Hz in established timing I/II
001121.138: HDMI:EDID found DMT format: code 6, 640x480p @ 75 Hz in established timing I/II
001121.177: HDMI:EDID found DMT format: code 9, 800x600p @ 60 Hz in established timing I/II
001121.214: HDMI:EDID found DMT format: code 10, 800x600p @ 72 Hz in established timing I/II
001121.252: HDMI:EDID found DMT format: code 11, 800x600p @ 75 Hz in established timing I/II
001121.292: HDMI:EDID found DMT format: code 16, 1024x768p @ 60 Hz in established timing I/II
001121.331: HDMI:EDID found DMT format: code 17, 1024x768p @ 70 Hz in established timing I/II
001121.369: HDMI:EDID found DMT format: code 18, 1024x768p @ 75 Hz in established timing I/II
001121.411: HDMI:EDID found DMT format: code 36, 1280x1024p @ 75 Hz in established timing I/II
001121.493: HDMI:EDID standard timings block x 8: 0x714F 8100 8140 8180 9500 950F B300 A940
001121.544: HDMI:EDID found DMT format: code 21, 1152x864p @ 75 Hz (4:3) in standard timing 0
001121.594: HDMI:EDID found DMT format: code 28, 1280x800p @ 60 Hz (16:10) in standard timing 1
001121.644: HDMI:EDID found DMT format: code 32, 1280x960p @ 60 Hz (4:3) in standard timing 2
001121.694: HDMI:EDID found DMT format: code 35, 1280x1024p @ 60 Hz (5:4) in standard timing 3
001121.747: HDMI:EDID found DMT format: code 47, 1440x900p @ 60 Hz (16:10) in standard timing 4
001121.799: HDMI:EDID found DMT format: code 48, 1440x900p @ 75 Hz (16:10) in standard timing 5
001121.850: HDMI:EDID found DMT format: code 58, 1680x1050p @ 60 Hz (16:10) in standard timing 6
001121.901: HDMI:EDID found DMT format: code 51, 1600x1200p @ 60 Hz (4:3) in standard timing 7
001134.904: HDMI:EDID parsing v3 CEA extension 0
001134.942: HDMI:EDID monitor support - underscan IT formats:yes, basic audio:yes, yuv444:yes, yuv422:yes, #native DTD:1
001134.988: HDMI:EDID found CEA detail timing format: 1920x1080p @ 50 Hz (31)
001135.032: HDMI:EDID found CEA detail timing format: 1280x720p @ 50 Hz (19)
001135.076: HDMI:EDID found CEA detail timing format: 1920x1080i @ 50 Hz (20)
001135.112: HDMI:EDID found CEA format: code 16, 1920x1080p @ 60Hz (native)
001135.147: HDMI:EDID found CEA format: code 31, 1920x1080p @ 50Hz
001135.179: HDMI:EDID found CEA format: code 4, 1280x720p @ 60Hz
001135.212: HDMI:EDID found CEA format: code 19, 1280x720p @ 50Hz
001135.245: HDMI:EDID found CEA format: code 5, 1920x1080i @ 60Hz
001135.277: HDMI:EDID found CEA format: code 20, 1920x1080i @ 50Hz
001135.309: HDMI:EDID found CEA format: code 3, 720x480p @ 60Hz
001135.342: HDMI:EDID found CEA format: code 18, 720x576p @ 50Hz
001135.376: HDMI:EDID found CEA format: code 32, 1920x1080p @ 24Hz
001135.409: HDMI:EDID found CEA format: code 33, 1920x1080p @ 25Hz
001135.443: HDMI:EDID found CEA format: code 34, 1920x1080p @ 30Hz
001135.495: HDMI:EDID found audio format 2 channels PCM, sample rate: 32|44|48 kHz, sample size: 16|20|24 bits
001135.515: HDMI:EDID found Video Capability DB length 2
001135.543: HDMI:EDID video capability: CE:3 IT:3 PT:0 QS:0
001135.562: HDMI:EDID found HDMI VSDB length 18
001135.585: HDMI:EDID HDMI VSDB has physical address 3.0.0.0
001135.607: HDMI:EDID HDMI VSDB supports AI:yes, dual link DVI:no
001135.637: HDMI:EDID HDMI VSDB deep colour support - 48-bit:no 36-bit:yes 30-bit:yes DC_yuv444:yes
001135.655: HDMI:EDID HDMI VSDB max TMDS clock 225 MHz
001135.673: HDMI:EDID HDMI VSDB does not support content type
001135.696: HDMI:EDID HDMI VSDB supports 3D formats
001135.713: HDMI:EDID HDMI VSDB 3D_Mask: 0x073f
001135.732: HDMI:EDID HDMI VSDB 3D_Structure_All: 0x0140
001135.768: HDMI:EDID HDMI VSDB explicit 3D mode: 2D VIC order 4 (CEA 5), 3D struct 0x00, 3D detail 0x00
001135.804: HDMI:EDID HDMI VSDB explicit 3D mode: 2D VIC order 5 (CEA 20), 3D struct 0x00, 3D detail 0x00
001135.841: HDMI:EDID HDMI VSDB explicit 3D mode: 2D VIC order 9 (CEA 33), 3D struct 0x00, 3D detail 0x00
001135.880: HDMI:EDID HDMI VSDB explicit 3D mode: 2D VIC order 10 (CEA 34), 3D struct 0x00, 3D detail 0x00
001135.944: HDMI:EDID CEA (32) 1920x1080p 24Hz 3D supports: FP|TopBot|SbS-HH
001135.987: HDMI:EDID CEA (4) 1280x720p 60Hz 3D supports: FP|TopBot|SbS-HH
001136.031: HDMI:EDID CEA (5) 1920x1080i 60Hz 3D supports: FP|TopBot|SbS-HH
001136.076: HDMI:EDID CEA (19) 1280x720p 50Hz 3D supports: FP|TopBot|SbS-HH
001136.123: HDMI:EDID CEA (20) 1920x1080i 50Hz 3D supports: FP|TopBot|SbS-HH
001136.164: HDMI:EDID CEA (16) 1920x1080p 60Hz 3D supports: TopBot|SbS-HH
001136.205: HDMI:EDID CEA (31) 1920x1080p 50Hz 3D supports: TopBot|SbS-HH
001136.242: HDMI:EDID CEA (3) 720x480p 60Hz 3D supports: none
001136.278: HDMI:EDID CEA (18) 720x576p 50Hz 3D supports: none
001136.325: HDMI:EDID CEA (33) 1920x1080p 25Hz 3D supports: FP|TopBot|SbS-HH
001136.371: HDMI:EDID CEA (34) 1920x1080p 30Hz 3D supports: FP|TopBot|SbS-HH
001136.407: HDMI:EDID filtering formats with pixel clock > 162 MHz or h. blanking > 1023
001136.672: HDMI:EDID preferred mode remained as CEA (16) 1920x1080p @ 60 Hz with pixel clock 148 MHz
001141.360: HDMI:Setting property pixel encoding to Default
001141.378: HDMI:Setting property pixel clock type to PAL
001141.399: HDMI:Setting property content type flag to No data
001141.420: HDMI:Setting property fuzzy format match to enabled
001153.202: gpioman: gpioman_get_pin_num: pin LEDS_RUNNING not defined
001153.228: gpioman: gpioman_get_pin_num: pin LEDS_NAND_ACTIVITY not defined
001153.251: gpioman: gpioman_get_pin_num: pin LEDS_USB_ACTIVITY not defined
001153.273: gpioman: gpioman_get_pin_num: pin LEDS_FATAL_ERROR not defined
001153.293: gpioman: gpioman_get_pin_num: pin LEDS_APP_OK not defined
001153.314: gpioman: gpioman_get_pin_num: pin LEDS_APP_FAILED not defined
001153.336: gpioman: gpioman_get_pin_num: pin LEDS_HDCP_AUTH not defined
001153.357: gpioman: gpioman_get_pin_num: pin LEDS_HDCP_UNAUTH not defined
001153.376: gpioman: gpioman_get_pin_num: pin LEDS_HDMI_ON not defined
001153.397: gpioman: gpioman_get_pin_num: pin LEDS_DVI_ON not defined
001153.417: gpioman: gpioman_get_pin_num: pin LEDS_HDMI_HPD_UP not defined
001153.440: gpioman: gpioman_get_pin_num: pin LEDS_REMOTE_CONTROL not defined
001153.463: gpioman: gpioman_get_pin_num: pin LEDS_ARM_CONTROLLED not defined
001172.460: hdmi: HDMI:>>>>>>>>>>>>>Rx sensed, reading EDID<<<<<<<<<<<<<
001184.591: hdmi: HDMI:EDID version 1.3, 1 extensions, screen size 112x63 cm
001184.662: hdmi: HDMI:EDID features - videodef 0x80 !standby !suspend !active off; colour encoding:RGB444|YCbCr422; sRGB is not default colourspace; preferred format is native; does not support GTF
001184.725: hdmi: HDMI:EDID found preferred CEA detail timing format: 1920x1080p @ 60 Hz (16)
001184.795: hdmi: HDMI:EDID found DMT detail timing format: 1360x768p @ 60 Hz (39)
001184.838: hdmi: HDMI:EDID found DMT format: code 4, 640x480p @ 60 Hz in established timing I/II
001184.878: hdmi: HDMI:EDID found DMT format: code 5, 640x480p @ 72 Hz in established timing I/II
001184.921: hdmi: HDMI:EDID found DMT format: code 6, 640x480p @ 75 Hz in established timing I/II
001184.961: hdmi: HDMI:EDID found DMT format: code 9, 800x600p @ 60 Hz in established timing I/II
001185.003: hdmi: HDMI:EDID found DMT format: code 10, 800x600p @ 72 Hz in established timing I/II
001185.044: hdmi: HDMI:EDID found DMT format: code 11, 800x600p @ 75 Hz in established timing I/II
001185.086: hdmi: HDMI:EDID found DMT format: code 16, 1024x768p @ 60 Hz in established timing I/II
001185.127: hdmi: HDMI:EDID found DMT format: code 17, 1024x768p @ 70 Hz in established timing I/II
001185.170: hdmi: HDMI:EDID found DMT format: code 18, 1024x768p @ 75 Hz in established timing I/II
001185.213: hdmi: HDMI:EDID found DMT format: code 36, 1280x1024p @ 75 Hz in established timing I/II
001185.302: hdmi: HDMI:EDID standard timings block x 8: 0x714F 8100 8140 8180 9500 950F B300 A940
001185.357: hdmi: HDMI:EDID found DMT format: code 21, 1152x864p @ 75 Hz (4:3) in standard timing 0
001185.411: hdmi: HDMI:EDID found DMT format: code 28, 1280x800p @ 60 Hz (16:10) in standard timing 1
001185.463: hdmi: HDMI:EDID found DMT format: code 32, 1280x960p @ 60 Hz (4:3) in standard timing 2
001185.518: hdmi: HDMI:EDID found DMT format: code 35, 1280x1024p @ 60 Hz (5:4) in standard timing 3
001185.572: hdmi: HDMI:EDID found DMT format: code 47, 1440x900p @ 60 Hz (16:10) in standard timing 4
001185.625: hdmi: HDMI:EDID found DMT format: code 48, 1440x900p @ 75 Hz (16:10) in standard timing 5
001185.683: hdmi: HDMI:EDID found DMT format: code 58, 1680x1050p @ 60 Hz (16:10) in standard timing 6
001185.736: hdmi: HDMI:EDID found DMT format: code 51, 1600x1200p @ 60 Hz (4:3) in standard timing 7
001198.739: hdmi: HDMI:EDID parsing v3 CEA extension 0
001198.779: hdmi: HDMI:EDID monitor support - underscan IT formats:yes, basic audio:yes, yuv444:yes, yuv422:yes, #native DTD:1
001198.827: hdmi: HDMI:EDID found CEA detail timing format: 1920x1080p @ 50 Hz (31)
001198.872: hdmi: HDMI:EDID found CEA detail timing format: 1280x720p @ 50 Hz (19)
001198.921: hdmi: HDMI:EDID found CEA detail timing format: 1920x1080i @ 50 Hz (20)
001198.962: hdmi: HDMI:EDID found CEA format: code 16, 1920x1080p @ 60Hz (native)
001198.998: hdmi: HDMI:EDID found CEA format: code 31, 1920x1080p @ 50Hz
001199.035: hdmi: HDMI:EDID found CEA format: code 4, 1280x720p @ 60Hz
001199.071: hdmi: HDMI:EDID found CEA format: code 19, 1280x720p @ 50Hz
001199.108: hdmi: HDMI:EDID found CEA format: code 5, 1920x1080i @ 60Hz
001199.145: hdmi: HDMI:EDID found CEA format: code 20, 1920x1080i @ 50Hz
001199.181: hdmi: HDMI:EDID found CEA format: code 3, 720x480p @ 60Hz
001199.217: hdmi: HDMI:EDID found CEA format: code 18, 720x576p @ 50Hz
001199.252: hdmi: HDMI:EDID found CEA format: code 32, 1920x1080p @ 24Hz
001199.290: hdmi: HDMI:EDID found CEA format: code 33, 1920x1080p @ 25Hz
001199.325: hdmi: HDMI:EDID found CEA format: code 34, 1920x1080p @ 30Hz
001199.382: hdmi: HDMI:EDID found audio format 2 channels PCM, sample rate: 32|44|48 kHz, sample size: 16|20|24 bits
001199.404: hdmi: HDMI:EDID found Video Capability DB length 2
001199.433: hdmi: HDMI:EDID video capability: CE:3 IT:3 PT:0 QS:0
001199.453: hdmi: HDMI:EDID found HDMI VSDB length 18
001199.483: hdmi: HDMI:EDID HDMI VSDB has physical address 3.0.0.0
001199.507: hdmi: HDMI:EDID HDMI VSDB supports AI:yes, dual link DVI:no
001199.540: hdmi: HDMI:EDID HDMI VSDB deep colour support - 48-bit:no 36-bit:yes 30-bit:yes DC_yuv444:yes
001199.563: hdmi: HDMI:EDID HDMI VSDB max TMDS clock 225 MHz
001199.582: hdmi: HDMI:EDID HDMI VSDB does not support content type
001199.606: hdmi: HDMI:EDID HDMI VSDB supports 3D formats
001199.628: hdmi: HDMI:EDID HDMI VSDB 3D_Mask: 0x073f
001199.649: hdmi: HDMI:EDID HDMI VSDB 3D_Structure_All: 0x0140
001199.691: hdmi: HDMI:EDID HDMI VSDB explicit 3D mode: 2D VIC order 4 (CEA 5), 3D struct 0x00, 3D detail 0x00
001199.733: hdmi: HDMI:EDID HDMI VSDB explicit 3D mode: 2D VIC order 5 (CEA 20), 3D struct 0x00, 3D detail 0x00
001199.776: hdmi: HDMI:EDID HDMI VSDB explicit 3D mode: 2D VIC order 9 (CEA 33), 3D struct 0x00, 3D detail 0x00
001199.816: hdmi: HDMI:EDID HDMI VSDB explicit 3D mode: 2D VIC order 10 (CEA 34), 3D struct 0x00, 3D detail 0x00
001199.885: hdmi: HDMI:EDID CEA (32) 1920x1080p 24Hz 3D supports: FP|TopBot|SbS-HH
001199.935: hdmi: HDMI:EDID CEA (4) 1280x720p 60Hz 3D supports: FP|TopBot|SbS-HH
001199.984: hdmi: HDMI:EDID CEA (5) 1920x1080i 60Hz 3D supports: FP|TopBot|SbS-HH
001200.034: hdmi: HDMI:EDID CEA (19) 1280x720p 50Hz 3D supports: FP|TopBot|SbS-HH
001200.083: hdmi: HDMI:EDID CEA (20) 1920x1080i 50Hz 3D supports: FP|TopBot|SbS-HH
001200.130: hdmi: HDMI:EDID CEA (16) 1920x1080p 60Hz 3D supports: TopBot|SbS-HH
001200.177: hdmi: HDMI:EDID CEA (31) 1920x1080p 50Hz 3D supports: TopBot|SbS-HH
001200.215: hdmi: HDMI:EDID CEA (3) 720x480p 60Hz 3D supports: none
001200.256: hdmi: HDMI:EDID CEA (18) 720x576p 50Hz 3D supports: none
001200.305: hdmi: HDMI:EDID CEA (33) 1920x1080p 25Hz 3D supports: FP|TopBot|SbS-HH
001200.353: hdmi: HDMI:EDID CEA (34) 1920x1080p 30Hz 3D supports: FP|TopBot|SbS-HH
001200.391: hdmi: HDMI:EDID filtering formats with pixel clock > 162 MHz or h. blanking > 1023
001200.656: hdmi: HDMI:EDID preferred mode remained as CEA (16) 1920x1080p @ 60 Hz with pixel clock 148 MHz
001200.678: hdmi: HDMI: hotplug attached with HDMI support
001200.746: hdmi: HDMI:hdmi_get_state is deprecated, use hdmi_get_display_state instead
001203.224: hdmi: HDMI: power_on to CEA mode 1080p60
001205.387: hdmi: HDMI: Action callback added to queue to happen at frame 2
001205.409: hdmi: HDMI: Action stop_3d_mode added to queue to happen at frame 2
001205.432: hdmi: HDMI: Action unmute added to queue to happen at frame 3
001255.625: *** Restart logging

001256.529: Read command line from file 'cmdline.txt'
boot=/dev/mmcblk0p1 disk=/dev/mmcblk0p2 quiet

001258.245: Can't find 'kernel7.img' on boot device - rc 2
001258.305: Loading 'kernel.img' from SD card
001583.119: Kernel trailer DTOK property says yes
001583.140: Kernel trailer DDTK property says no
001583.265: Loading 'bcm2709-rpi-2-b.dtb' from SD card
001587.568: dtdebug: /aliases:i2c_vc=i2c0
001590.411: dtdebug: /__symbols__:i2c_vc=i2c0
001592.931: dtdebug: /__overrides__:i2c_vc=i2c0
001597.537: dtdebug: /__overrides__:i2c_vc_baudrate=i2c0_baudrate
001599.563: dtdebug: /aliases:i2c=i2c1
001602.434: dtdebug: /__symbols__:i2c=i2c1
001605.005: dtdebug: /__overrides__:i2c=i2c1
001607.097: dtdebug: /aliases:i2c_arm=i2c1
001610.028: dtdebug: /__symbols__:i2c_arm=i2c1
001612.664: dtdebug: /__overrides__:i2c_arm=i2c1
001617.436: dtdebug: /__overrides__:i2c_baudrate=i2c1_baudrate
001622.255: dtdebug: /__overrides__:i2c_arm_baudrate=i2c1_baudrate
001622.274: dtparam: pwr_led_gpio=35
001623.898: dtdebug: Found override pwr_led_gpio
001623.936: dtdebug: override pwr_led_gpio: cell target gpios @ offset 4 (size 4)
001631.175: Loaded overlay 'hifiberry-digi'
001641.775: dtdebug: Found fragment 0 (offset 36)
001642.888: dtdebug: merge_fragment(/sound,/fragment@0/__overlay__)
001642.912: dtdebug: +prop(compatible)
001644.042: dtdebug: +prop(i2s-controller)
001645.456: dtdebug: +prop(status)
001646.668: dtdebug: merge_fragment() end
001646.730: dtdebug: Found fragment 1 (offset 168)
001649.588: dtdebug: merge_fragment(/soc/i2s@7e203000,/fragment@1/__overlay__)
001649.610: dtdebug: +prop(status)
001650.526: dtdebug: merge_fragment() end
001650.611: dtdebug: Found fragment 2 (offset 244)
001654.921: dtdebug: merge_fragment(/soc/i2c@7e804000,/fragment@2/__overlay__)
001654.947: dtdebug: +prop(#address-cells)
001655.715: dtdebug: +prop(#size-cells)
001656.480: dtdebug: +prop(status)
001659.326: dtdebug: merge_fragment(/soc/i2c@7e804000/wm8804@3b,/fragment@2/__overlay__/wm8804@3b)
001659.348: dtdebug: +prop(#sound-dai-cells)
001660.178: dtdebug: +prop(compatible)
001660.912: dtdebug: +prop(reg)
001661.702: dtdebug: +prop(status)
001662.516: dtdebug: merge_fragment() end
001662.543: dtdebug: merge_fragment() end
001664.747: dtparam: arm_freq=900000000
001666.254: dtdebug: Found override arm_freq
001666.297: dtdebug: override arm_freq: cell target clock-frequency @ offset 0 (size 4)
001671.025: dtdebug: override arm_freq: cell target clock-frequency @ offset 0 (size 4)
001675.822: dtdebug: override arm_freq: cell target clock-frequency @ offset 0 (size 4)
001680.720: dtdebug: override arm_freq: cell target clock-frequency @ offset 0 (size 4)
001685.668: dtparam: cache_line_size=64
001687.365: dtdebug: /__overrides__ has no cache_line_size property
001687.378: Unknown param 'cache_line_size' - ignored
001732.659: dtdebug: delete_node(/hat)
001747.824: gpioman: gpioman_get_pin_num: pin SDCARD_CONTROL_POWER not defined
002599.114: vchiq_core: vchiq_init_state: slot_zero = 0xeec80000, is_master = 1
002602.765: hdmi: HDMI:hdmi_get_state is deprecated, use hdmi_get_display_state instead
002606.565: gpioman: gpioman_get_pin_num: pin LEDS_RUNNING not defined
002606.591: gpioman: gpioman_get_pin_num: pin LEDS_NAND_ACTIVITY not defined
002606.614: gpioman: gpioman_get_pin_num: pin LEDS_USB_ACTIVITY not defined
002606.636: gpioman: gpioman_get_pin_num: pin LEDS_FATAL_ERROR not defined
002606.657: gpioman: gpioman_get_pin_num: pin LEDS_APP_OK not defined
002606.678: gpioman: gpioman_get_pin_num: pin LEDS_APP_FAILED not defined
002606.700: gpioman: gpioman_get_pin_num: pin LEDS_HDCP_AUTH not defined
002606.721: gpioman: gpioman_get_pin_num: pin LEDS_HDCP_UNAUTH not defined
002606.740: gpioman: gpioman_get_pin_num: pin LEDS_HDMI_ON not defined
002606.763: gpioman: gpioman_get_pin_num: pin LEDS_DVI_ON not defined
002606.783: gpioman: gpioman_get_pin_num: pin LEDS_HDMI_HPD_UP not defined
002606.808: gpioman: gpioman_get_pin_num: pin LEDS_REMOTE_CONTROL not defined
002606.830: gpioman: gpioman_get_pin_num: pin LEDS_ARM_CONTROLLED not defined
002607.192: TV service:host side not connected, dropping notification 0x00000002, 0x00000001, 0x00000010
010336.358: hdmi: HDMI:Setting property pixel clock type to NTSC
010336.465: hdmi: HDMI: power_on to CEA mode 1080p60
010336.517: hdmi: HDMI: Action detach added to queue to happen at frame 545
010336.542: hdmi: HDMI: Action change_mode added to queue to happen at frame 545
010336.563: hdmi: HDMI: Action attach added to queue to happen at frame 545
010336.584: hdmi: HDMI: Action start_mode added to queue to happen at frame 545
010336.609: hdmi: HDMI: Action callback added to queue to happen at frame 547
010336.632: hdmi: HDMI: Action stop_3d_mode added to queue to happen at frame 547
010336.655: hdmi: HDMI: Action unmute added to queue to happen at frame 548
010723.878: hdmi: HDMI:Setting property pixel clock type to NTSC
010723.984: hdmi: HDMI: power_on to CEA mode 1080p60
010724.037: hdmi: HDMI: Action detach added to queue to happen at frame 569
010724.061: hdmi: HDMI: Action change_mode added to queue to happen at frame 569
010724.083: hdmi: HDMI: Action attach added to queue to happen at frame 569
010724.106: hdmi: HDMI: Action start_mode added to queue to happen at frame 569
010724.130: hdmi: HDMI: Action callback added to queue to happen at frame 571
010724.152: hdmi: HDMI: Action stop_3d_mode added to queue to happen at frame 571
010724.176: hdmi: HDMI: Action unmute added to queue to happen at frame 572
OpenELEC-Basement:~ #

my Config.txt file

################################################################################
# This file is part of OpenELEC - http://www.openelec.tv
# Copyright (C) 2009-2014 Stephan Raue (stephan@openelec.tv)
# Inspired and partly copied from:
# http://youresuchageek.blogspot.fr/2012/09/howto-raspberry-pi-openelec-on.html
#
# OpenELEC is free software: you can redistribute it and/or modify
# it under the terms of the GNU General Public License as published by
# the Free Software Foundation, either version 2 of the License, or
# (at your option) any later version.
#
# OpenELEC is distributed in the hope that it will be useful,
# but WITHOUT ANY WARRANTY; without even the implied warranty of
# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
# GNU General Public License for more details.
#
# You should have received a copy of the GNU General Public License
# along with OpenELEC. If not, see <http://www.gnu.org/licenses/>.
################################################################################
# Bootloader configuration - config.txt
################################################################################

dtoverlay=hifiberry-digi
dtdebug=1

################################################################################
# Memory (System/GPU configuration )
################################################################################

# default GPU memory split (do not change if you do not know what you are doing)
gpu_mem=128

# SDRAM size based GPU memory split, uncomment and setup to override 'gpu_mem'
gpu_mem_256=112
gpu_mem_512=160
gpu_mem_1024=256

################################################################################
# Overclocking settings
# WARNING: Do not change/enable if you do not know what you are doing!
# The System may become unstable or you can have data corruption or
# you can loose your warranty if you set wrong settings
#
# please read: http://elinux.org/RPi_config.txt#Overclocking_configuration
################################################################################

# Overclock mode settings.
#
# default recommended values are: arm_freq | core_freq | sdram_freq | over_voltage
# no overclocking : 700 | 250 | 400 | 0
# mode 'Modest' : 800 | 300 | 400 | 0
# mode 'Medium' : 900 | 333 | 450 | 2
# mode 'High' : 950 | 450 | 450 | 6
# mode 'Turbo' : 1000 | 500 | 500 | 6

# arm_freq=700
# core_freq=250
# sdram_freq=400
# over_voltage=0

# set to 'force_turbo=1' to disable dynamic overclocking (you can lose your warranty!)
force_turbo=0

# If you have any data corruption using Turbo Mode and overclocking
# try with this setting uncommented
# If this still fails, try to use Medium mode without "over_voltage=2"
# If it ultimately keeps failing, forget about this until it gets fixed
# Use a more conservative mode that will works fine in any cases:
# initial_turbo=30

################################################################################
# Overscan settings
################################################################################

# Make display smaller to stop text spilling off the screen
# see also http://www.raspberrypi.org/phpBB3/viewtopic.php?f=67&t=15700
# overscan_scale=1
# disable_overscan=1

# Adapt overscan values to your needs
# overscan_left=57
# overscan_right=59
# overscan_top=20
# overscan_bottom=20

################################################################################
# various settings see also: http://elinux.org/RPi_config.txt
################################################################################

# Force HDMI even if unplugged or powered off
# hdmi_force_hotplug=1

# Doesn't sent initial active source message.
# Avoids bringing CEC (enabled TV) out of standby and channel switch when
# rebooting.
hdmi_ignore_cec_init=1

################################################################################
# License keys to enable GPU hardware decoding for various codecs
# to obtain keys visit the shop at http://www.raspberrypi.com
################################################################################

# decode_MPG2=0x00000000
# decode_WVC1=0x00000000
# decode_DTS=0x00000000
# decode_DDP=0x00000000

################################################################################
# End of default configuration
# all values below this line were inserted from config.txt.bk (your old config)
# and can be merged with the above values
################################################################################

I then tried to run the system using the sound test image, with yet again no sound.
The output on screen was this (please accept my apologies for the poor image quality):


Please help...

• Facebook
• Twitter
• LinkedIn

30 comments

• 0
  
  HiFiBerry team August 15, 2015 05:19

  Hi,
  
  this looks good so far. Does the optical output light up with the test image? How did you connect the Digi to your DAC?
  
  Best regards
  Daniel
• 0
  
  Yaron Zamir August 15, 2015 11:12

  Hi Daniel.
  
  Thank you for the fast reply at this time of the week.
  
  The Digi is connected to my Yamaha receiver using the optical interface, and it seems to light up in constant red,
  But no sound comes out of the speakers. When I plug the same optical cord to another sound source, like the old streamer I wanted to replace by this RPI-DIGI combo, sound comes out as expected.
  
  
• 0
  
  Yaron Zamir August 15, 2015 12:02

  In addition to my last post, the optical connector on the Digi+ lights up only when running the sound test image.
  With OpenELEC the connector stays dormant.
  
  
• 0
  
  HiFiBerry team August 15, 2015 12:47

  Ok, this tells us that your OpenElec configuration is incorrect. Did you select the sound card in the settings menu?
  
  Best regards
  Daniel
• 0
  
  Yaron Zamir August 15, 2015 13:36

  Hi Daniel.
  
  The sound card did not appear as an option in the setting menu, all i can see is the 3 regular options:
  HDMI, Analogue, HDMI and Analogue.
  
  Since yesterday i have tried your beta stage installation app: http://downloads.hifiberry.com/HiFiBerry_Installer.exe
  suggested by Stuart of your team at a post i stumbled on. I must say that the App, although in early stage, and doesn't have all options (like OpenELEC v5.95 RC2 - maybe on purpose) makes the installation process much easier.
  
  Since it is still in Beta, kindly let me point out 3 bugs that i found:
  1. Although i chose the DIGI+ option in the third option screen, browsing at the config.txt generates reveals that the app added dtoverlay=hifiberry-dacplus to the file.
  2. The image was written successfully to the SD-Card, but exiting the app results in a crash with a windows (7 64Bit) error message giving the choice to stop the app or try to find for a solution online.
  3. A minor bug - when choosing OpenELEC you get a link on the screen which suppose to direct you to an OpenELEC explanatory web page. this link doesn't work.
  
  Using the SD-Card obviously did not improve my problem situation, as the sound card still does not appear as an option in the Aoudio settings of Kodi (v14.2), but changing the param in config.txt to toverlay=hifiberry-digi
  resulted in a better situation for me, since the sound card is no available as an option in the audio settings pannel within Kodi.
  
  I chose the sound card as the output device, pass-through enabled, ac3 and DTS checked, and pass-through device - my DIGI+ card. The optical light is turned on, and all seems OK except for the fact that sound does not come out from my speakers.
  
  Furthermore - my Receiver shows "Input Data Error" on it's panel, when trying to play a clip (a youtube clip).
  I tried the RCA connection connected to an SPD/IF input in the receiver, with exact same results.
  
  Connecting the optical cable to another source proves OK, and also when i change the audio settings to HDMI i get sound out of my TV speakers as expected.
  
  As i see it - i have 2 problems:
  1. Manual configuration of the Digi card - although relatively not complicated - did not work for me in OpenElec v5.95 + Kody v15 rc2.
  2. Even when the DIGI+ card is recognized (Using your Installation app, or the Sound test image), no sound comes out of the speakers, and the receiver shows "Input Data Error" both with optical interface and Coax RCA cable.
  
  Don't really know were to go from here...
  
  Help please...
• 0
  
  HiFiBerry team August 15, 2015 14:26

  Hi,
  
  the "Input data error" comes from an older kernel on the test image. This shouldn't be a problem with OpenElec.
  When you login to your OpenElec, what is the output of "aplay -l"?
  
  Best regards
  Daniel
• 0
  
  Yaron Zamir August 15, 2015 23:42

  Hi Daniel,
  
  I get the “Input data error” when using the test system based on OpenELEC v5.0.8 installation i built using the http://downloads.hifiberry.com/HiFiBerry_Installer.exe.
  
  the output of the aplay -l in this environment is:
  
  

  
  OpenELEC (official) Version: 5.0.8
  OpenELEC:~ # aplay -l
  **** List of PLAYBACK Hardware Devices ****
  card 0: sndrpihifiberry [snd_rpi_hifiberry_digi], device 0: HifiBerry Digi HiFi wm8804-spdif-0 []
  Subdevices: 1/1
  Subdevice #0: subdevice #0
  OpenELEC:~ #
  

  
  
  When using my working system - OpenELEC v5.95.3 the output of the aplay -l is:
  

  
  OpenELEC-Basement:~ # aplay -l
  aplay: device_list:268: no soundcards found…
  

  
  
  
• 0
  
  HiFiBerry team August 16, 2015 06:10

  Hi Yaron,
  
  looks like something in OpenElec 5.95 is broken. We can have a look, but most likely the OpenElec developers have to fix this. Until this is fixed, I recommend staying with 5.0.8
  
  Best regards
  Daniel
• 0
  
  Rossken August 16, 2015 09:36

  Hello,
  
  I just did un update of the OpenElec and my spdif doesn't work anymore on my hifiberry rb pi 2b digi+.
  I reinstalled the 5.0.8 with your installer: http://downloads.hifiberry.com/HiFiBerry_Installer.exe, but i don't see anymore the option to activate the spdif. I hope somebody can help me out?
  
  Best regards,
  
  Bart..
• 0
  
  HiFiBerry team August 16, 2015 10:05

  Hi Rossken,
  
  the installer still has a bug and enables HiFiBerry DAC. Please edit /flash/config.txt and use dtoverlay=hifiberry-digi
  
  Best regards
  Daniel
• 0
  
  Rossken August 16, 2015 10:13

  Daniel,
  
  Thanks for the quick reply on my question. I understand your solution, but i don't find the directory /flash/
  I find a config file where i see the boot loader config txt. I think this isn't the place to change it, no?
  
  Regards,
  
  Bart..
• 0
  
  HiFiBerry team August 16, 2015 10:16

  Yes, this is the right directory. You're editing on your PC - right?
  
  Best regards
  Daniel
• 0
  
  Rossken August 16, 2015 10:20

  Yes, i also see that the parameters are different of my cpu, gpu and voltage.
  But i don't see any text about my spdif or audio.
  Can i maybe send my config file, so you can see what's different?
  
  Regards,
  
  Bart..
• 0
  
  HiFiBerry team August 16, 2015 10:26

  Ignore the CPU and voltage stuff. You need to have a line
  
  dtoverlay=hifiberry-digi
  
  There might be a line dtoverlay=hifiberry-dacplus which is incorrect and needs to be removed.
  
  Best regards
  Daniel
• 0
  
  Rossken August 16, 2015 10:27

  ok thanks, i check it right now.
  
  Rgds,
  
  Bart..
• 0
  
  Rossken August 16, 2015 10:37

  Thanks, find it, with the incorrect line. Just changed it, testing and yesss works fine now.
  The only reason why i updated the openelec was because i always have problems with my buffer. My internet connection is good, speed download of 140 mb/s so i don't think that's the problem.
  So it isn't interesting to upgrade momently to isengard yet?
  
  rgds,
  
  Bart..
• 0
  
  HiFiBerry team August 16, 2015 10:46

  Hi,
  
  we need to look into this first and see what kind of bug is it. Then the OpenElec developers have to fix it. Before this we don't recommend upgrading.
  
  Best regards
  Daniel
• 0
  
  Rossken August 16, 2015 10:51

  Thanks Daniel for the solution. I will wait for an official update of the OpenElec.
  
  
  Regards,
  
  Bart..
• 0
  
  Yaron Zamir August 16, 2015 11:35

  Hi.
  
  The card is recognized indeed when I am using it in the OpenELEC v5.0.8 + Kodi 14.2 which I built using your install app, however, even when selecting it in the Kodi audio settings I still can't get anything out of my speakers. Instead I get a "Data Input Error" message displayed on my Yamaha DSP-A1 receiver. This happens with both interfaces I try, the optical or the coaxial-RCA.
  
  Yaron.
• 0
  
  HiFiBerry team August 16, 2015 16:58

  Hi Yaron,
  
  the "Input data error" on the DSP-A1 happens with older kernels. Can you please check the kernel version with
  uname -a
  
  Best regards
  Daniel
• 0
  
  Yaron Zamir August 17, 2015 04:22

  Hi Daniel.
  
  Here is the output of "uname -l"
  
  

  
  OpenELEC:~ # uname -a
  Linux OpenELEC 3.18.10 #1 SMP Tue Mar 31 14:50:33 CEST 2015 armv7l GNU/Linux
  OpenELEC:~ #
  

  
  
  The installation is the one created automatically by your installation App.
  
  In System Info screen within Kodi it says:
  

  
  Operating system: OpenELEC (official - Version 5.0.8 (Kernel 3.18.10)
  

  
  
  Yaron
• 0
  
  HiFiBerry team August 17, 2015 07:28

  Hi Yaron,
  
  yes, it looks like this is still an kernel that does not have the right patch integrated. You have 2 options: Wait until 5.95 is fixed or check out OSMC.
  
  Best regards
  Daniel
• 0
  
  Yaron Zamir August 17, 2015 08:05

  Hi Daniel.
  
  I am a little bit confused right now.
  Does this mean that the HifiBerry DIGI+ is not supported under OpenELEC 5.0.8 (which is the current stable version), and also will not work with the OpenELEC beta versions 5.95.x? No customer of the DIGI+ card have succeeded to make it work under the current stable version OpenELEC?
  
  I think i used the same system as Rossken built successfully as described few post above this. We both used your beta installation app to create an OpenELEC 5.0.8 system, with the same Kernel version, and the same Kodi version. We both also corrected the wrong PARAM in the config.txt file. In both cases the Audio card is recognized within Kodi and can be selected.
  
  How come that it is working fine for Rossken, but not for me? What am i doing wrong?
  
  Best regards
  Yaron
• 0
  
  HiFiBerry team August 17, 2015 08:19

  Hi Yaron,
  
  your receiver needs a specific patch that was introduced in April. As the kernel on the 5.0.8 OpenElec is still older it does not include this patch. For 99% of the users this is not an issue, but your receiver needs this patch. Therefore it won't work with older kernel versions.
  
  Best regards
  Daniel
• 0
  
  Yaron Zamir August 18, 2015 04:27

  Hi Daniel.
  
  Thank you for your reply, I think I understand the problem now.
  Can't say that I'm not somewhat disappointed, but hey, no one promised a perfect life.
  
  Not all - however, is dark. Snooping around in the net I found out that others also encountered my initial problem in which the HifiBerry DIGI+ audio card is not recognized in systems based on OpenELEC most recent beta version - v5.95.3. Moreover- it seems that the card was recognized perfectly in the previous beta Of OpenELEC v5.95.2, and stopped being detected correctly just in the most recent version, the one I chose to use …
  
  I then downgraded my system to v5.95.2, and the Digi+ card is recognize do, and can be selected both as the output sound card, and the pass-through card in Kodi's Audio settings screen, and I get great sound from my speakers when playing a source that contains DTS sound track.
  
  Still it is not a full solution since I don't get any sound when playing a media that contains an AC3 (Dolby Digital) audio track. DTS is working, AC3 (DD 5.1) doesn't. Same media plays well using my old Xtreamer Pro.
  
  Did you encounter this problem before? Is it the same problem or a new one?
  
  Thank you for you patience,
  Best regards,
  Yaron
• 0
  
  Rossken August 19, 2015 19:20

  @Daniel, with your installation file i installed i still have some problems. Please could you check this debug.log file?
  http://xbmclogs.com/pg2mhzw43
  
  Regards,
  
  Bart..
• 0
  
  HiFiBerry team August 20, 2015 04:42

  Hi,
  
  I can't debug OpenElec. I'm not an OpenElec developer. We just provide guides for users how to configure OpenElec. For any OpenElec specific debugging you need to talk to the OpenElec developers.
  
  Best regards
  Daniel
• 0
  
  Stuart MacLean August 20, 2015 17:02

  Hi
  
  In looking at the OpenELEC 5.95 beta version I can confirm it is indeed broken. It looks like the 4.1.2 kernel is trying to load the device driver for the HiFiBerry card and it is seeing. However there appears to be a problem with the actual loading of the device driver.
  
  Using SSH and using
  
  aplay -l
  
  I see the soundcard being listed. However when trying to use either the Kodi media controls or more directly ALSA's ‘aplay’ for trying to achieve playback then there is no sound output. So the device driver looks like it is loaded, but something is failing (most likely on the kernel side of things) that is effectively stopping audio playback.
  
  The following output dmesg from the kernel booting up (in this case is using the AMP+) with Pi2. Also confirmed it is not working on the Digi+ and DAC+.
  
  From the start of the kernel boot
  
  

  [    0.000000] Booting Linux on physical CPU 0xf00
  [    0.000000] Linux version 4.1.2 (stephan@buildserver.openelec.tv) (gcc version 4.9.3 (GCC) ) #1 SMP Wed Jul 15 20:21:34 CEST 2015
  [    0.000000] CPU: ARMv7 Processor [410fc075] revision 5 (ARMv7), cr=10c5387d
  [    0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
  [    0.000000] Machine model: Raspberry Pi 2 Model B Rev 1.1
  [    0.000000] cma: Reserved 8 MiB at 0x2e800000
  [    0.000000] Memory policy: Data cache writealloc

  
  
  
  From it is loading the AMP+ module via the device overlay
  
  

  [    2.623717] systemd[1]: Starting Setup Timezone data...
  [    2.626036] systemd[1]: Started Debug /var/log relink.
  [    3.158452] systemd[1]: Started Load Kernel Modules.
  [    3.159948] systemd[1]: Started Create Static Device Nodes in /dev.
  [    3.161285] systemd[1]: Started Setup Timezone data.
  [    3.207588] systemd[1]: Started Journal Service.
  [    3.294222] systemd-journald[288]: Received request to flush runtime journal from PID 1
  [    4.658178] snd-rpi-hifiberry-dacplus sound: ASoC: CPU DAI (null) not registered
  [    4.658214] snd-rpi-hifiberry-dacplus sound: snd_soc_register_card() failed: -517
  [    4.660535] snd-rpi-hifiberry-dacplus sound: ASoC: CODEC DAI pcm512x-hifi not registered
  [    4.660564] snd-rpi-hifiberry-dacplus sound: snd_soc_register_card() failed: -517
  [    4.671986] snd-rpi-hifiberry-dacplus sound: pcm512x-hifi <-> 3f203000.i2s mapping ok
  [    4.734146] Console: switching to colour dummy device 80x30
  [    5.304974] smsc95xx 1-1.1:1.0 eth0: hardware isn't capable of remote wakeup
  [    5.305213] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
  [    5.802830] random: nonblocking pool is initialized
  [    7.036058] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
  [    7.039606] smsc95xx 1-1.1:1.0 eth0: link up, 100Mbps, full-duplex, lpa 0xC5E1
  [    7.210151] pcm512x 1-004d: No SCLK, using BCLK: -2
  [    7.215269] pcm512x 1-004d: No SCLK, using BCLK: -2
  [    7.220646] pcm512x 1-004d: No SCLK, using BCLK: -2

  
  
  
  and for the DAC+
  
  

  [    3.485105] systemd-journald[295]: Received request to flush runtime journal from PID 1
  [    5.152667] Console: switching to colour dummy device 80x30
  [    5.342000] snd-hifiberry-amp sound: ASoC: CPU DAI (null) not registered
  [    5.342034] snd-hifiberry-amp sound: snd_soc_register_card() failed: -517
  [    5.342285] snd-hifiberry-amp sound: ASoC: CPU DAI (null) not registered
  [    5.342301] snd-hifiberry-amp sound: snd_soc_register_card() failed: -517
  [    5.996136] smsc95xx 1-1.1:1.0 eth0: hardware isn't capable of remote wakeup
  [    5.996352] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
  [    6.184211] random: nonblocking pool is initialized
  [    6.417956] snd-hifiberry-amp sound: tas5713-hifi <-> 3f203000.i2s mapping ok
  [    7.583230] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready

  
  
  
  Best Regards
  
  Stuart
• 0
  
  Yaron Zamir August 21, 2015 03:39

  Hi Stuart.
  
  This was exactly my problem when using OpenELEC v5.95 Beta 3.
  It seems that the problem exists only within the last Kernel v4.1.2 used with Beta 3.
  The Digi+ is recognized and produces sound (at least partially - in my case) when using the previous OpenELEC v5.95 Beta 2.
  Fortunately it seems that OpenELEC team are aware of the problem, and possibly already made a correction to be hopefully included in the next Beta/GA version 6.
  
  I downgraded to the previous beta, and using pass-through - i get sound from my speakers as long as the sound track is DTS (full 5.1 channels), however i don't get any sound when the sound track is AC3/DD (5.1 or otherwise).
  Since most of the TV-Shows sound tracks are coded as AC3/Dolby Digital, this renders my PI2-Digi+ just half a solution, forcing me to still use my old Xtreamer Pro for the other half.
  
  Is it the same problem, or a new one? Did you encounter this problem before?
  
  Best Regards
  Yaron
• 0
  
  HiFiBerry team August 21, 2015 04:44

  Hi Yaron,
  
  many users use Dolby Digital with the HiFiBerry Digi+. I can't say if there is a specific problem with the version you're using or if your configuration needs to be changed. As this is a pure application-related issue, I recommend asking the OpenElec developers about this. They might be able to tell you how to debug this.
  
  Best regards
  Daniel